SN65HVD230Q-Q1

SN65HVD231Q-Q1

SN65HVD232Q-Q1

SGLS117C – JUNE 2001 – REVISED JUNE 2002

6

www.ti.com

absolute maximum ratings over operating free-air temperature (see Note 1) (unless otherwise

– 0.3 V to 6 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Voltage range at any bus terminal (CANH or CANL)

– 7 V to 16 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Voltage input range, transient pulse, CANH and CANL, through 100

Ω (see Figure 7)

– 25 V to 25 V

. . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Electrostatic discharge: Human body model (see Note 2)

CANH, CANL and GND

15 kV

. . . . . . . . . . . . . . . . . .

All pins

2.5 kV

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Charged-device model (see Note 3) All pins

4 kV

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Continuous total power dissipation

See Dissipation Rating table

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

– 65

°C to 150°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds

260

°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and

functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not

implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

NOTES:

1. All voltage values, except differential I/O bus voltages, are with respect to network ground terminal.

2. Tested in accordance with JEDEC Standard 22, Test Method A114-A.

3. Tested in accordance with JEDEC Standard 22, Test Method C101.

DISSIPATION RATING TABLE

PACKAGE

TA ≤ 25°C

POWER RATING

DERATING FACTOR‡

ABOVE TA = 25°C

TA = 70°C

POWER RATING

TA = 85°C

POWER RATING

TA = 125°C

POWER RATING

D

725 mW

5.8 mW/

°C

464 mW

377 mW

145 mW

‡ This is the inverse of the junction-to-ambient thermal resistance when board-mounted and with no air flow.

recommended operating conditions

PARAMETER

MIN

NOM

MAX

UNIT

Supply voltage, VCC

3

3.6

V

Voltage at any bus terminal (common mode) VIC

– 2§

7

V

Voltage at any bus terminal (separately) VI

– 2.5

7.5

V

High-level input voltage, VIH

D, R

2

V

Low-level input voltage, VIL

D, R

0.8

V

Differential input voltage, VID (see Figure 5)

–6

6

V

V(RS)

0

VCC

V

V(RS) for standby or sleep

0.75 VCC

VCC

V

Rs wave-shaping resistance

0

100

k

Ω

High level output current I

Driver

–40

mA

High-level output current, IOH

Receiver

–8

mA

Low level output current I

Driver

48

mA

Low-level output current, IOL

Receiver

8

mA

Operating free-air temperature, TA

–40

125

°C

§ The algebraic convention, in which the least positive (most negative) limit is designated as minimum is used in this data sheet.