| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
PIC18F4331 Datasheet(PDF) 236 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC18F4331 Datasheet(HTML) 236 Page - Microchip Technology |
|
236 / 396 page ![]() PIC18F2331/2431/4331/4431 DS39616B-page 234 Preliminary 2003 Microchip Technology Inc. To set up an Asynchronous Transmission: 1. Initialize the SPBRG register for the appropriate baud rate. If a high-speed baud rate is desired, set bit BRGH (see Section 19.2 “USART Baud Rate Generator (BRG)”). 2. Enable the asynchronous serial port by clearing bit SYNC and setting bit SPEN. 3. If interrupts are desired, set enable bit TXIE. 4. If 9-bit transmission is desired, set transmit bit TX9. Can be used as address/data bit. 5. Enable the transmission by setting bit TXEN, which will also set bit TXIF. 6. If 9-bit transmission is selected, the ninth bit should be loaded in bit TX9D. 7. Load data to the TXREG register (starts transmission). If using interrupts, ensure that the GIE and PEIE bits in the INTCON register (INTCON<7:6>) are set. FIGURE 19-6: ASYNCHRONOUS RECEPTION TABLE 19-6: REGISTERS ASSOCIATED WITH ASYNCHRONOUS RECEPTION Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on POR, BOR Value on all other Resets INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 0000 000x 0000 000u PIR1 — ADIF RCIF TXIF — CCP1IF TMR2IF TMR1IF -000 -000 -000 -000 PIE1 — ADIE RCIE TXIE — CCP1IE TMR2IE TMR1IE -000 -000 -000 -000 IPR1 — ADIP RCIP TXIP — CCP1IP TMR2IP TMR1IP -111 -111 -111 -111 RCSTA SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 0000 -00x 0000 -00x RCREG USART Receive Register 0000 0000 0000 0000 TXSTA CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 0000 0010 0000 0010 BAUDCTL — RCIDL — SCKP BRG16 — WUE ABDEN -1-1 0-00 -1-1 0-00 SPBRGH Baud Rate Generator Register, High Byte 0000 0000 0000 0000 SPBRG Baud Rate Generator Register, Low Byte 0000 0000 0000 0000 Legend: x = unknown, – = unimplemented locations read as ‘0’. Shaded cells are not used for Asynchronous Reception. Start bit bit7/8 bit1 bit0 bit7/8 bit0 Stop bit Start bit Start bit bit7/8 Stop bit RX (pin) Reg Rcv Buffer Reg Rcv Shift Read Rcv Buffer Reg RCREG RCIF (Interrupt Flag) OERR bit CREN Word 1 RCREG Word 2 RCREG Stop bit Note: This timing diagram shows three words appearing on the RX input. The RCREG (receive buffer) is read after the third word, causing the OERR (overrun) bit to be set. |
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |