Specifications

Supply Voltage and Current

Input Voltage: 12 V dc to 30 V dc (10% maximum ripple at 10% duty cycle)

Input Current: less than 88 mA at 12 V dc, less than 75 mA at 24 V dc and less

than 72 mA at 30 V dc (exclusive of load)

Supply Protection Circuitry

Protected against reverse polarity and transient overvoltages

Sensing Beam

Visible red, 630 nm

Sensing Range

Retroreflective applications: 2 m (6.5 ft) using 25 mm (1 in) wide

retroreflective tape

Diffuse applications: 400 mm (15.7 in) with 18% reflectivity gray card target

Sensing Height

4-channel models: 111 mm (4.4 in)

8-channel models: 240 mm (9.4 in)

Beam Spacing

28.6 mm (1.125 in)

Output Configuration

User-selectable via DIP switch:

1 open-collector PNP (current sourcing) or 1 open-collector NPN (current sinking)

Output Rating

150 mA maximum

OFF-state leakage current: less than 10 microamps

ON-state saturation voltage: NPN — less than 1 V dc at 150 mA; PNP — less than

2 V dc at 150 mA

Required Overcurrent Protection

WARNING: Electrical connections must be made

by qualified personnel in accordance with local and

national electrical codes and regulations.

Overcurrent protection is required to be provided by end product application per

the supplied table.

Overcurrent protection may be provided with external fusing or via Current

Limiting, Class 2 Power Supply.

Supply wiring leads < 24 AWG shall not be spliced.

For additional product support, go to http://www.bannerengineering.com.

Supply Wiring (AWG)

Required Overcurrent Protection (Amps)

20

5.0

22

3.0

24

2.0

26

1.0

28

0.8

30

0.5

Output Protection

Protected against false pulse on power-up and short circuit of outputs

Output Response Time

400 ms (includes standard 100 ms ON-delay and 100 ms OFF-delay)

Delay at Power-Up

Less than 1.0 second

Sensing Resolution

See Dimensions on page 6 for Minimum Object Detection Zone

Retroreflective: 51 mm at 406 mm range, 100 mm at 2 m (2.0 in dia. at 16 in

range, 3.9 in at 6.5 ft); see Figure 2 on page 2

Diffuse: 55 mm dia. at 400 mm range (2.16 in at 15.7 in range)

Indicators

Green LED: Power ON/OFF

Yellow LED: Output ON/OFF

Job Light (Diffused Green LED): Turned ON and OFF by applying an external

signal to the Job input (white wire). The job lights will be active high or active

low, depending on DIP switch 4 selection.

Error Light (Diffused Red LED): Turned ON and OFF by detection of an output

event when job light is not ON.

Indicator Light Lumens

Light Function

Color

Typical Wavelength

Typical Intensity (lm)

Job Light

Green

525 nm

12

Error Light

Red

625 nm

2.5

Adjustments

4 DIP switches, located behind access panel (default setting is ON position)

Construction

Black painted aluminum housing; acrylic lenses; thermoplastic polyester end

caps; thermoplastic elastomer programming switch cover; stainless steel

mounting brackets and hardware

Connections

5-conductor PVC-jacketed 2 m (6.5 ft) cable which is either unterminated or

terminated with a 5-pin Euro-style quick-disconnect connector, depending on

model. Cable diameter is 3.3 mm (0.13 in).

Environmental Rating

NEMA 2; IEC IEC IP62

Operating Conditions

Temperature: 0 °C to +50 °C (+32 °F to +122 °F)

Humidity: 90% at +50 °C maximum relative humidity (non-condensing)

Certifications

PVD Series Parts Verification Sensor

P/N 113230 Rev. G

www.bannerengineering.com - Tel: +1-763-544-3164

5