| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
M37534RSS Datasheet(PDF) 19 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
M37534RSS Datasheet(HTML) 19 Page - Renesas Technology Corp |
|
19 / 55 page ![]() 7534 Group Rev.2.00 Jun 21, 2004 page 19 of 54 REJ03B0099-0200Z Timers The 7534 Group has 3 timers: timer X, timer 1 and timer 2. The division ratio of every timer and prescaler is 1/(n+1) provided that the value of the timer latch or prescaler is n. All the timers are down count timers. When a timer reaches “0”, an underflow occurs at the next count pulse, and the corresponding timer latch is reloaded into the timer. When a timer underflows, the inter- rupt request bit corresponding to each timer is set to “1”. qTimer 1, Timer 2 Prescaler 12 always counts f(XIN)/16. Timer 1 and timer 2 always count the prescaler output and periodically sets the interrupt request bit. qTimer X Timer X can be selected in one of 4 operating modes by setting the timer X mode register. • Timer Mode The timer counts the signal selected by the timer X count source selection bit. • Pulse Output Mode The timer counts the signal selected by the timer X count source selection bit, and outputs a signal whose polarity is inverted each time the timer value reaches “0”, from the CNTR0 pin. When the CNTR0 active edge switch bit is “0”, the output of the CNTR0 pin is started with an “H” output. At “1”, this output is started with an “L” output. When using a timer in this mode, set the port P14 direction register to output mode. • Event Counter Mode The operation in the event counter mode is the same as that in the timer mode except that the timer counts the input signal from the CNTR0 pin. When the CNTR0 active edge switch bit is “0”, the timer counts the rising edge of the CNTR0 pin. When this bit is “1”, the timer counts the falling edge of the CNTR0 pin. • Pulse Width Measurement Mode When the CNTR0 active edge switch bit is “0”, the timer counts the signal selected by the timer X count source selection bit while the CNTR0 pin is “H”. When this bit is “1”, the timer counts the signal while the CNTR0 pin is “L”. In any mode, the timer count can be stopped by setting the timer X count stop bit to “1”. Each time the timer overflows, the interrupt request bit is set. Fig. 19 Structure of timer X mode register Fig. 20 Timer count source set register Timer X mode register (TM : Address 002B 16) CNTR0 active edge switch bit 0 : Interrupt at falling edge Count at rising edge (in event counter mode) 1 : Interrupt at rising edge Count at falling edge (in event counter mode) Timer X operating mode bits b1 b0 0 0 : Timer mode 0 1 : Pulse output mode 1 0 : Event counter mode 1 1 : Pulse width measurement mode Not used (return “0” when read) Timer X count stop bit 0 : Count start 1 : Count stop b7 b0 Timer count source set register (TCSS : Address 002E 16) b7 b0 Timer X count source selection bit (Note) 0 : f(XIN)/16 1 : f(XIN)/2 Not used (return “0” when read) Note : To switch the timer X count source selection bit , stop the timer X count operation. |
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |