V19

2

Specifications

TR30RAM Series Derating Curve

INPUT SPECIFICATIONS:

Voltage …....………........…........................................... 90~264Vac

Frequency ………………………………………….…………..…..... 47 to 63Hz

Input Current …………………........... 100Vac/0.8A max., 240Vac/0.4A max.

Inrush Current ………………..….…Cold start@25℃ 100A max. @240Vac

Leakage Current …………………………………………………… 100µA max.

OUTPUT SPECIFICATIONS:

Hold-up Time …………………………………………… 10ms typ. @115Vac

Short Circuit Protection …………….………… Hiccup Mode (Auto Recovery)

NOTE:

Over Voltage Protection ………………. ............... TVS Component to Clamp

1. Voltage accuracy is set at 60% load and 25℃ Ta.

Temperature Coefficient ……………………............................… ±0.05%/℃

2. Add a 0.1uF ceramic capacitor and a 10uF E.L. capacitor to output for

GENERAL SPECIFICATIONS:

Ripple & Noise measuring @20MHz BW.

Isolation …………………………… Input to output = 4,000VAC (5,656VDC)

3. Line regulation measured from 100Vac to 240Vac with full load.

Operating Temperature .................................. 0 ~ 60℃(see drating curve)

4. Load regulation measured from 60% to full load and from 60% to

Storage Temperature ……………………………...….......……........ -20~85℃

20% load (60% +/- 40% load)

Humidity …………………...….......….......... 93% RH max. Non condensing

5. Typical efficiency with 230 VAC and max. load at 25°C.

Cooling …………………………………………………….. Natural Convection

6. ”Various TR Series adapters are PSE certified. PSE certification

Switching Frequency ………………………………………….. 70KHz Typical

alone is not sufficient for importation into Japan. A valid PSE mark

MTBF ……..…..… MIL-HDBK-217F, GB, 25℃/115VAC ….... 200Khrs min.

must contain the name of the importer as shown in the example below.

Altitude …………………………………………………………………… 3000m

If PSE mark is required, the name of the registered importer must be

Dimensions ……..….. 4.278x2.440x1.445Inches (108.67x61.98x36.70mm)

supplied to Cincon on order placement. Product labels will not contain

Weight ……………………………………………………… 300g(0.67 Pounds)

PSE mark if importer name is not supplied. Consult factory or local

SAFETY AND EMC:

representative for details”

Emission and lmmunity (Ed. 4.0) …. EN55011 Class B, FCC CFR47 Part 18 Class B

EN60601-1-2, EN61000-3-2-3, EN61000-4-2, 3, 4, 5, 6, 8, 11

Safety (Ed. 3.1) ………………………………..… IEC60601-1:2005+A1:2012

EN60601-1:2006+A11:2011+A1+A12, UL ANSI/AAMI ES60601-1:2005

IEC 60950-1, EN60950-1, UL60950-1

Mechanical Specification

Millimeters:X.XX±0.5

Tolerance:Inches:X.XXX±0.02

All Dimensions are in inches(mm)

70.866[1800.00]±1.969[50.00]

18AWG／1800mm

DC Plug :Straight(ψ5.5／ψ2.1) L12mm

DC Plug type: V+ ─●)─ V-

4.278[108.67]

+

-

Typical at 25˚C, nominal line and 75% load, unless otherwise Specified

0%

20%

40%

60%

80%

100%

0

10

20

30

40

50

60

20LFM(Natural Convection)