Technical Data

Function indicator

Emitter: Yellow LED, illuminates at high emitting power, off at low emitting power

Receiver: Yellow LED: illuminates when an object is detected flashes when falling

short of the stability control (4 Hz)

Error message: Yellow LED flashes (8 Hz) in emitter and receiver

Control elements

Receiver: 2 touch buttons for programming

Parameterization indicator

IO link communication: green LED goes out briefly (1 Hz)

Electrical specifications

Operating voltage

18 ... 30 V DC

Ripple

10 %

No-load supply current

Emitter ≤: 50 mA

Receiver: ≤ 150 mA (without outputs)

Time delay before availability

see Table 1, max. 2.3 s

Interface

Interface type

IO-Link

Protocol

IO-Link V1.0

Mode

COM 2 (38.4 kBaud)

Input

Test input

Emitter switch-off with +UB or 0 V at pin 4 (emitter)

Function input

Range input activation from 1.6 m (or 2 m in case of option /35) with +UB or 0 V on pin

2 (emitter)

Teach-In input for programming on pin 8 (receiver)

Output

Pre-fault indication output

Stability Control (SC) 1 PNP, short-circuit protected, reverse polarity protected on pin 2

(receiver)

Switching type

Factory setting: dark on , Switchable to light-on mode

Signal output

Switch output (detection field C/Q) 1 push-pull (4 in 1) output, short-circuit protected,

reverse polarity protected on pin 4 (receiver),

Height monitoring (H1, H2. H3) 3 push-pull (4 in 1) outputs, short-circuit proof, reverse

polarity protected on pin 5, pin 6, pin 7 (receiver)

Switching threshold

Factory setting: The signal tracking for the threshold value is deactivated, increasing

the optical resolution by a maximum of 4 mm; switchable to active signal tracking

Switching voltage

max. 30 V DC

Switching current

max. 100 mA

Voltage drop

≤ 2 V DC

Switching frequency

f

see Table 1, max. 135 Hz

Response time

see Table 1, max. 12 ms

Timer function

Off-delay programmable from 0 ... 1.25 s in 5 ms steps (adjustment via IO-Link only)

Conformity

Communication interface

IEC 61131-9

Product standard

EN 60947-5-2

Approvals and certificates

Protection class

III ( IEC 61140 )

UL approval

cULus Listed

CCC approval

CCC approval / marking not required for products rated ≤36 V

Ambient conditions

Ambient temperature

Standard : -10 ... 60 °C (14 ... 140 °F)

Option /146: -30 ... 60 °C (-22 ... 140 °F)

Storage temperature

-30 ... 70 °C (-22 ... 158 °F)

Mechanical specifications

Conductor cross section

Housing width

20 mm

Housing depth

30.5 mm

Housing length L

see Table 1, max. 3360 mm

Degree of protection

IP67

Connection

Emitter: connecting cable with 4-pin, M12 x 1 connector , 330 mm total length

Receiver: connecting cable with 8-pin, M12 x 1 connector , 350 mm total length

Material

Housing

extruded aluminum section , Silver anodized

Light grid

LGS25

3

Germany: +49 621 776 1111

Pepperl+Fuchs Group

Refer to "General Notes Relating to Pepperl+Fuchs Product Information".

USA: +1 330 486 0001

Singapore: +65 6779 9091

www.pepperl-fuchs.com

fa-info@us.pepperl-fuchs.com

fa-info@sg.pepperl-fuchs.com

fa-info@de.pepperl-fuchs.com