DGD2136

Document Number DS38611 Rev. 7 - 4

5 of 14

www.diodes.com

November 2021

© Diodes Incorporated

DGD2136

DC Electrical Characteristics (VBIAS (VCC, VBS) = 15V, @TA = +25°C, unless otherwise specified.) (Note 7)

Parameter

Symbol

Min

Typ

Max

Unit

Condition

Logic “0” Input Voltage (Note 8)

VIH

2.4

–

–

V

–

Logic “1” Input Voltage (Note 8)

VIL

–

–

0.8

V

–

High Level Output Voltage, VBIAS - VO

VOH

–

–

0.1

V

IO = 0mA

Low Level Output Voltage, VO

VOL

–

–

0.1

V

IO = 0mA

Offset Supply Leakage Current

ILK

–

–

10

µA

VB = VS = 600V

Quiescent VBS Supply Current

IBSQ

10

85

130

µA

VIN = 0V or 5V, EN = 0V

Quiescent VCC Supply Current

ICCQ

–

1.1

1.6

mA

VIN = 0V or 5V, EN = 0V

Logic Input Bias Current (HO=LO=HIGH)

IIN+

–

130

200

µA

VIN = 0V

Logic Input Bias Current (HO=LO=LOW)

IIN-

–

3.0

20

µA

VIN = 5V

Logic Enable “1” Input Bias Current

IEN+

–

33

80

µA

VEN = 5V

Logic Enable “0” Input Bias Current

IEN-

–

–

2.0

µA

VEN = 0V

VBS Supply Undervoltage Positive Going Threshold

VBSUV+

7.6

8.9

9.9

V

–

VBS Supply Undervoltage Negative Going Threshold

VBSUV-

7.1

8.3

9.4

V

–

VCC Supply Undervoltage Positive Going Threshold

VCCUV+

7.6

8.9

9.9

V

–

VCC Supply Undervoltage Negative Going Threshold

VCCUV-

7.1

8.3

9.4

V

–

Output High Short Circuit Pulsed Current

IO+

120

200

–

mA

VO = 0V, PW ≤ 10µs

Output Low Short Circuit Pulsed Current

IO-

250

350

–

mA

VO = 15V, PW ≤ 10µs

Overcurrent Detect Positive Threshold

VITH+

400

500

600

mV

–

Overcurrent Detect Negative Threshold

VITH-

340

420

500

mV

–

Short-Circuit Input Current

ICSIN

6.0

11

16

µA

VCSIN = 1V

RCIN Positive Going Threshold Voltage

VRCINTH+

7.0

8.4

9.8

V

–

RCIN Negative Going Threshold Voltage

VRCINTH-

–

5.0

–

V

–

Fault Output Low Level Voltage

VFOL

–

0.2

0.5

V

VCS = 1V, IFO = 1.5mA

RCIN on Resistance

RDSRCIN

40

75

110



IRCIN = 1.5mA

Fault Output on Resistance

RDSFO

80

130

180



IFO = 1.5mA

Notes:

7. The VIN, VTH and IIN parameters are referenced to VSS and are applicable to all six channels (HIN1*, 2*, 3* and LIN1*, 2*, 3*). The VO and IO

parameters are applicable to the output pins (HO1, 2, 3 and LO1, 2, 3) and are referenced to COM.

8. For optimal operation, it is recommended that the input pulses (HIN1*, 2*, 3* and LIN1*, 2*, 3*) should have a minimum amplitude of 2.4V with a

minimum pulse width of 600ns.

AC Electrical Characteristics (VBIAS (VCC, VBS) = 15V, CL = 1000pF, @TA = +25°C, unless otherwise specified.)

Parameter

Symbol

Min

Typ

Max

Unit

Condition

Turn-On Propagation Delay

tON

200

330

460

ns

VS = 0V

Turn-Off Propagation Delay

tOFF

200

330

460

ns

VS = 0V

Turn-On Rise Time

tR

–

90

150

ns

VS = 0V

Turn-Off Fall Time

tF

–

35

60

ns

VS = 0V

Delay Matching

tDM

–

–

50

ns

–

Enable Low to Output Shutdown Delay

tEN

225

300

425

ns

–

ITRIP Pin Leading-Edge Blanking Time

tBLT

200

300

400

ns

–

Time from ITRIP Triggering to FO*

tFLT

360

550

760

ns

From VITRIP = 1V to

FO* turn off

Time from ITRIP Triggering to All Gate Outputs Turn

Off

tITRIP

420

615

820

ns

From VITRIP = 1V to

starting gate turn off

Input Filtering Time (HIN*, LIN*, EN)

tFLTIN

–

250

–

ns

–

Fault Clear Time

tFLTCLR

–

1.6

–

ms

CRCIN = 1nF,

RRCIN = 2M

Deadtime

tDT

200

290

420

ns

–

Deadtime Matching

tDTM

–

–

50

ns

–

Output Pulse Width Matching (Note 8)

tPM

–

50

75

ns

PWIN > 1µs

Note:

8. tPM is defined as PWIN – PWOUT.