STM32U595QJ datasheet(34/377 Pages) STMICROELECTRONICS

34 / 377 page

Functional overview

STM32U59xxx

34/377

DS13633 Rev 1

•

Power supply supervision

–

BOR monitor

–PVD monitor

–

PVM monitor (VDDA, VDDUSB, VDDIO2)

•

Power management

–

Operating modes

–

Voltage scaling control

–

Low-power modes

•

VBAT battery charging

•

TrustZone security and privileged protection

3.9.1

Power supply schemes

The devices require a 1.71 V to 3.6 V VDD operating voltage supply. Several independent

supplies can be provided for specific peripherals:

•

VDD = 1.71 V to 3.6 V (functionality guaranteed down to VBORx min value)

VDD is the external power supply for the I/Os, the internal regulator and the system

analog such as reset, power management and internal clocks. It is provided externally

through the VDD pins.

•

VDDA = 1.58 V (COMPs) / 1.6 V (DACs, OPAMPs) / 1.62 V (ADCs) /

1.8 V (VREFBUF) to 3.6 V

VDDA is the external analog power supply for ADCs, DACs, voltage reference buffer,

operational amplifiers and comparators. The VDDA voltage level is independent from

the VDD voltage and must be connected to VDD or VSS pin (preferably to VDD) when

these peripherals are not used.

•

VDDSMPS = 1.71 V to 3.6 V

VDDSMPS is the external power supply for the SMPS step-down converter. It is provided

externally through VDDSMPS supply pin. It must be connected to the same supply as

VDD pin when the SMPS is used in the application. When the SMPS is not used, it is

recommended to connect both VDDSMPS and VLXSMPS to GND.

•

VLXSMPS is the switched SMPS step down converter output.

Note:

The SMPS power supply pins are available only on a specific package with SMPS step

down converter option.

•

VDDUSB = 3.0 V to 3.6 V

VDDUSB is the external independent power supply for USB transceivers. VDDUSB

voltage level is independent from the VDD voltage and must be connected to VDD or

VSS pin (preferably to VDD) when the USB is not used.

•

VDD11USB = 1.0 V to 1.26 V

VDD11USB is the external power supply for the USB transceiver. This supply is only

available on specific packages and must be connected to VDD11.

•

VDDIO2 = 1.08 V to 3.6 V

VDDIO2 is the external power supply for 14 I/Os (port G[15:2]). The VDDIO2 voltage level

is independent from the VDD voltage and must be connected to VDD or VSS pin

(preferably to VDD) when PG[15:2] are not used.

•

VBAT = 1.65 V to 3.6 V (functionality guaranteed down to VBOR_VBAT min value)

VBAT is the power supply for RTC, TAMP, external and internal 32 kHz oscillators, and

STM32U595QJ Datasheet(PDF) 34 Page - STMicroelectronics

STM32U595QJ Datasheet(HTML) 34 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL