| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
S32K310 Datasheet(PDF) 62 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
S32K310 Datasheet(HTML) 62 Page - NXP Semiconductors |
|
62 / 136 page ![]() Table 24. GPIO DC electrical specifications, 3.3V Range (2.97V - 3.63V) (continued) Symbol Description Min Typ Max Unit Condition Spec Number Standard Plus GPIO 4,6 and external 10pF, total 25pF load FMAX_33_M 3.3V maximum frequency for Medium GPIO 4,6 — — 50 MHz 2.9V - 3.6V, internal 5pF, PCB trace ~10pF and external 10pF, total 25pF load — FMAX_33_F 3.3V maximum frequency for Fast GPIO 4,6 — — 120 MHz 2.9V - 3.6V, internal 5pF, PCB trace ~10pF and external 10pF, total 25pF load — IOHT Output high current total for all ports 7 — — 100 mA — — 1. Maximum length of RESET pulse will be filtered by an internal filter on this pin. 2. Minimum length of RESET pulse, guaranteed not to be filtered by the internal filter. 3. A positive value is leakage flowing into pin with pin at VDD_HV_A/B (the GPIO supply level); a negative value is leakage flowing out the pin with the pin at ground. 4. GPIO output transition time information can be obtained from the device IBIS model. IBIS models are recommended for system level simulations, as discrete values for I/O transition times are not representative of the I/O pad behavior when connected to an actual transmission line load. 5. I/O output current specifications are valid for the given reference load figure, and the constraints given in the Operating Conditions of this document. 6. I/O timing specifications are valid for the un-terminated transmission line reference load given in the figure below. A lumped 8pF load is assumed at the end of a 5 inch microstrip trace on standard FR4 with approximately 1.5pF/inch (25pF total with margin). For signals with frequency greater than 63MHz, a maximum 2 inch PCB trace is assumed. 7. To determine total switching current on any I/O supply, current values per output pin should not be incrementally summed. I/O interfaces on the device are asynchronous to each other, so not all switching occurs at the same instant. Actual use case must be considered. RDSON RPCB = RDSON PCB External device MCUsee note 1 RDSON 5 in. (4 layer FR4) CPCB = ~1.5 pF/inch * 5 inch = ~7.5 pF CL = 8 pF 1. See IBIS models for further details. Notes: Figure 30. Reference Load Diagram 7.2 GPIO DC electrical specifications, 5.0V (4.5V - 5.5V) The leakage current on the GPIO pins is specified as a function of the pad type (Standard, Standard Plus, Medium, Fast, or GPI) and the number of Analog functions (CMP and ADC channels) multiplexed per pin. For S32K388, see the ILKG column in the Pinout section of the IOMUX file attached to the Reference Manual. NXP Semiconductors I/O parameters S32K3xx Data Sheet, Rev. 8, 06/2023 Data Sheet: Technical Data Preliminary Information for S32K3x8 62 / 136 |
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |