MCP621 datasheet(5/68 Pages) MICROCHIP

5 / 68 page

 2009-2021 Microchip Technology Inc. and its subsidiaries

DS20002188E-page 5

MCP621/1S/2/3/4/5/9

TABLE 1-3:

DIGITAL ELECTRICAL SPECIFICATIONS

Electrical Characteristics: Unless otherwise indicated, TA = +25°C, VDD = +2.5V to +5.5V, VSS = GND, VCM = VDD/

2, VOUT  VDD/2, VL = VDD/2, RL = 2 k to VL, CL = 50 pF and CAL/CS =VSS (refer to Figure 1-1 and Figure 1-2).

Parameters

Sym.

Min.

Typ.

Max.

Units

Conditions

CAL/CS Low Specifications

CAL/CS Logic Threshold, Low

VIL

VSS

—0.2VDD

CAL/CS Input Current, Low

ICSL

—0

—

CAL/CS = 0V

CAL/CS High Specifications

CAL/CS Logic Threshold, High

VIH

0.8VDD

VDD

CAL/CS Input Current, High

ICSH

—0.7

—

µA

CAL/CS = VDD

GND Current

ISS

-3.5

-1.8

—

µA

Single, CAL/CS = VDD = 2.5V

ISS

-8

-4

—

µA

Single, CAL/CS = VDD = 5.5V

ISS

-5

-2.5

—

µA

Dual, CAL/CS = VDD = 2.5V

ISS

-10

-5

—

µA

Dual, CAL/CS = VDD = 5.5V

CAL/CS Internal Pull-Down

Resistor

RPD

—5

—



Amplifier Output Leakage

IO(LEAK)

—

CAL/CS = VDD, TA = 125°C

POR Dynamic Specifications

VDD Low to Amplifier Off Time

(output goes High Z)

tPOFF

—

200

—

G = +1 V/V, VL = VSS,

VDD = 2.5V to 0V step to VOUT =0.1

(2.5V)

VDD High to Amplifier On Time

(including calibration)

tPON

100

200

300

G = +1 V/V, VL = VSS,

VDD = 0V to 2.5V step to VOUT =0.9

(2.5V)

CAL/CS Dynamic Specifications

CAL/CS Input Hysteresis

VHYST

—

0.25

—

CAL/CS Setup Time

(between CAL/CS edges)

tCSU

1—

—

µs

G = +1 V/V, VL = VSS (Notes 2, 3, 4)

CAL/CS = 0.8VDD to VOUT = 0.1 (VDD/

CAL/CS High to Amplifier Off Time

(output goes High Z)

tCOFF

—

200

—

G = +1 V/V, VL = VSS,

CAL/CS = 0.8VDD to VOUT = 0.1 (VDD/

CAL/CS Low to Amplifier On Time

(including calibration)

tCON

—3

G = +1 V/V, VL = VSS, MCP621 and

MCP625, CAL/CS = 0.2VDD to

VOUT =0.9 (VDD/2)

tCON

—6

G = +1 V/V, VL = VSS, MCP629,

CAL/CS = 0.2VDD to

VOUT =0.9 (VDD/2)

Note 1:

The MCP622 single, MCP625 dual and MCP629 quad have their CAL/CS inputs internally pulled down to VSS (0V).

This time ensures that the internal logic recognizes the edge. However, for the rising edge case, if CAL/CS is raised

before the calibration is complete, the calibration will be aborted and the part will return to Low-Power mode.

For the MCP625 dual, there is an additional constraint. CALA/CSA and CALB/CSB can be toggled simultaneously

(within a time much smaller than tCSU) to make both op amps perform the same function simultaneously. If they are

toggled independently, then CALA/CSA (CALB/CSB) cannot be allowed to toggle while op amp B (op amp A) is in

Calibration mode; allow more than the maximum tCON time (4 ms) before the other side is toggled.

For the MCP629 quad, there is an additional constraint. CALAD/CSAD and CALBC/CSBC can be toggled simultaneously

(within a time much smaller than tCSU) to make all four op amps perform the same function simultaneously, and the

maximum tCON time is approximately doubled (8 ms). If they are toggled independently, then CALAD/CSAD (CALBC/

CSBC) cannot be allowed to toggle while op amps B and C (op amps A and D) are in Calibration mode; allow more than

the maximum tCON time (8 ms) before the other side is toggled.

MCP621 Datasheet(PDF) 5 Page - Microchip Technology

MCP621 Datasheet(HTML) 5 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68

Datasheet Descarga

Enlace URL