LXT971ABC datasheet(23/90 Pages) INTEL

23 / 90 page

LXT971A 3.3V Dual-Speed Fast Ethernet Transceiver

Datasheet

Document #: 249414

Revision #: 002

Rev. Date: August 7, 2002

3.2.1.3

Fault Detection and Reporting

The LXT971A supports two fault detection and reporting mechanisms. “Remote Fault” refers to a

MAC-to-MAC communication function that is essentially transparent to PHY layer devices. It is

used only during auto-negotiation, and is applicable only to twisted-pair links. “Far-End Fault” is

an optional PMA-layer function that may be embedded within PHY devices. The LXT971A

supports both functions (see Section 3.2.1.3.1 and Section 3.2.1.3.2).

3.2.1.3.1 Remote Fault

indications. It is typically used when re-starting the auto-negotiation sequence to indicate to the

link partner that the link is down because the advertising device detected a fault.

When the LXT971A receives a Remote Fault indication from its partner during auto-negotiation it

does the following:

• Sets Register bit 5.13 in the Link Partner Base Page Ability Register, and

• Sets the Remote Fault Register bit 1.4 in the MII Status Register to pass this information to the

local controller.

3.2.1.3.2 100BASE-FX Far-End Fault

The SD/TP pin monitors signal quality during normal operation in fiber mode. If the signal quality

degrades beyond the fault threshold, the fiber transceiver reports a signal quality fault condition via

the SD/TP pin. Loss of signal quality blocks any fiber data from being received and causes a link

loss.

If the LXT971A detects a signal fault condition, it can transmit the Far-End Fault Indication (FEFI)

over the fiber link. The FEFI consists of 84 consecutive ones followed by a single zero. This

pattern must be repeated at least three times. The LXT971A transmits the far-end fault code a

minimum of three times if all the following conditions are true:

• Fiber mode is selected.

• Fault Code transmission is enabled (Register bit 16.2 = 1).

• Either Signal Detect indicates no signal or the receive PLL cannot lock.

• Loopback is not enabled.

3.2.2

MII Data Interface

The LXT971A supports a standard Media Independent Interface (MII). The MII consists of a data

interface and a management interface. The MII Data Interface passes data between the LXT971A

and a Media Access Controller (MAC). Separate parallel buses are provided for transmit and

receive. This interface operates at either 10 Mbps or 100 Mbps. The speed is set automatically,

once the operating conditions of the network link have been determined. Refer to “MII Operation”

on page 32 for additional details.

3.2.2.1

Increased MII Drive Strength

A higher Media Independent Interface (MII) drive strength may be desired in some designs to drive

signals over longer PCB trace lengths, or over high-capacitive loads, through multiple vias, or

through a connector. The MII drive strength in the LXT971A can be increased by setting Register

LXT971ABC Datasheet(PDF) 23 Page - Intel Corporation

LXT971ABC Datasheet(HTML) 23 Page - Intel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90

Datasheet Descarga

Enlace URL