| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
A19360LUBATN-RPR8 Datasheet(PDF) 4 Page - Allegro MicroSystems |
|
|
|||||||||||||||||||||||||||||
A19360LUBATN-RPR8 Datasheet(HTML) 4 Page - Allegro MicroSystems |
|
4 / 18 page ![]() High-Resolution GMR Wheel Speed and Distance Sensor IC A19360 4 Allegro MicroSystems 955 Perimeter Road Manchester, NH 03103-3353 U.S.A. www.allegromicro.com Continued on the next page… OPERATING CHARACTERISTICS: Valid throughout full operating voltage and temperature ranges, unless otherwise specified Characteristic Symbol Test Conditions Min. Typ. [1] Max. Unit ELECTRICAL CHARACTERISTICS Supply Voltage[2] VCC Potential between pin 1 and pin 2 -xxRx variant[3] 4.25 – 24 V -xxEx variant 5.2 – 24 V Undervoltage Lockout (UVLO) VCC(OFF) VCC switch off – – 3.5 V UVLO Hysteresis VHYS -xxRx variant 0.5 – – V -xxEx variant 1.5 – – V Reverse Supply Current[4] IRCC VCC = VRCC(MAX) –10 – – mA Supply Zener Clamp Voltage VZsupply ICC = ICC(MAX) + 3 mA 28 – – V Supply Current ICC(LOW) Low-current state 5.88 7 8.4 mA ICC(MID) Mid-current state 11.76 14 16.8 mA ICC(HIGH) High-current state 23.52 28 33.6 mA Supply Current Ratio [5] ICC(MID)/ICC(LOW) (isothermal) 1.9 – – – ICC(HIGH)/ICC(LOW) (isothermal) 3.8 – – – Fault Current IFAULT Refer to the figure in the Output Protocol in Fault Condition section 1 – 3.8 mA Fault Current Duration tW(FAULT) Refer to the figure in the Output Protocol in Fault Condition section 4 – 7 ms Output Rise, Fall Slew Rate SR RL = 50 Ω, CL = 10 pF, measured between 10% and 90% of signal 8 – 28 mA/μs POWER-ON CHARACTERISTICS Power-On State POS VCC > VCC(min), as connected in Figure 3 ICC(LOW) mA Power-On Time[6] tPO VCC > VCC(min), as connected in Figure 3 – – 1 ms Calibration Time TCAL Post tPO time to first AK protocol output event (f < 200 Hz) -xAx8 variant – 0.75 1.25 TCYCLE -xAx4 variant – 1 1.5 TCYCLE Post tPO time to first valid direction event (f < 200 Hz) -xxx8 variant – 0.75 1.25 TCYCLE -xxx4 variant – 1 1.5 TCYCLE [1] Typical values are at TA = 25°C and VCC = 12 V. Performance may vary for individual units, within the specified maximum and minimum limits. [2] Maximum voltage must be adjusted for power dissipation and junction temperature; see representative Power Derating section. [3] Part switching may cause the part to re-enter UVLO when this option is used with the AK protocol and a 50 Ω load. [4] Negative current is defined as conventional current coming out of (sourced from) the specified device terminal. [5] Supply current ratios are taken as the mean value of ICC(MID) / ICC(LOW) and the mean value of ICC(HIGH) / ICC(LOW), respectively. [6] Time between power-on to ICC stabilizing; output transients prior to tPO should be ignored. |
|
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |