TC2014_06 datasheet(2/20 Pages) MICROCHIP

2 / 20 page

TC2014/2015/2185

DS21662E-page 2

1.0

ELECTRICAL

CHARACTERISTICS

Absolute Maximum Ratings †

Input Voltage ................................................................... 7.0V

Output Voltage ....................................... (– 0.3) to (VIN + 0.3)

Operating Temperature ......................... – 40°C < TJ < 125°C

Storage Temperature.................................. – 65°C to +150°C

Maximum Voltage on Any Pin ................ VIN +0.3V to – 0.3V

Maximum Junction Temperature ...................... ............ 150°C

† Notice: Stresses above those listed under "Absolute

Maximum Ratings" may cause permanent damage to

the device. These are stress ratings only and functional

operation of the device at these or any other conditions

above those indicated in the operation sections of the

specifications is not implied. Exposure to Absolute

Maximum Rating conditions for extended periods may

affect device reliability.

ELECTRICAL CHARACTERISTICS

Electrical Specifications: Unless otherwise specified, VIN = VR + 1V, IL = 100 µA, COUT = 3.3 µF, SHDN > VIH, TA = +25°C.

BOLDFACE type specifications apply for junction temperature of -40°C to +125°C.

Parameters

Sym

Min

Typ

Max

Units

Conditions

Input Operating Voltage

VIN

2.7

—

6.0

Note 1

Maximum Output

Current

IOUTMAX

——

TC2014

100

——

TC2015

150

——

TC2185

Output Voltage

VOUT

VR – 2.0% VR ± 0.4% VR + 2.0%

Note 2

VOUT Temperature

Coefficient

TCVOUT

—

ppm/°C Note 3

—

Line Regulation

ΔVOUT/ΔVIN

—0.05

0.5

%(VR + 1V) < VIN < 6V

Load Regulation

(Note 4)

ΔVOUT/VOUT

-1.0

0.33

+1.0

TC2014;TC2015:IL = 0.1 mA to IOUTMAX

-2.0

0.43

+2.0

TC2185:IL = 0.1 mA to IOUTMAX (Note 4)

Dropout Voltage

VIN – VOUT

—2

—

Note 5

IL = 100 µA

—45

IL = 50 mA

—90

140

TC2015; TC2185 IL = 100 mA

—

140

210

TC2185

IL = 150 mA

Supply Current

IIN

—55

µA

SHDN = VIH, IL = 0

Shutdown Supply

Current

IINSD

—

0.05

0.5

µA

SHDN = 0V

Power Supply

Rejection Ratio

PSRR

—

≤ 1 kHz, Cbypass = 0.01 µF

Output Short Circuit

Current

IOUTSC

—

160

300

VOUT = 0V

Note 1: The minimum VIN has to meet two conditions: VIN = 2.7V and VIN = VR + VDROPOUT.

2: VR is the regulator output voltage setting. For example: VR = 1.8V, 2.7V, 2.8V, 2.85V, 3.0V, 3.3V.

4: Regulation is measured at a constant junction temperature using low duty cycle pulse testing. Load regulation is tested

over a load range from 1.0 mA to the maximum specified output current. Changes in output voltage due to heating

effects are covered by the Thermal Regulation specification.

5: Dropout Voltage is defined as the input-to-output differential at which the output voltage drops 2% below its nominal

value.

6: Thermal Regulation is defined as the change in output voltage at a time T after a change in power dissipation is applied,

excluding load or line regulation effects. Specifications are for a current pulse equal to IMAX at VIN = 6V for T = 10 ms.

7: The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction

temperature and the thermal resistance from junction-to-air (i.e. TA, TJ, θJA).

8: Time required for VOUT to reach 95% of VR (output voltage setting), after VSHDN is switched from 0 to VIN.

TCVOUT

VOUTMAX VOUTMIN

–

() 10

–

VOUT

----------------------------------------------------------------------------

TC2014 Datasheet(PDF) 2 Page - Microchip Technology

TC2014 Datasheet(HTML) 2 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Datasheet Descarga

Enlace URL