PS700 datasheet(10/38 Pages) MICROCHIP

10 / 38 page

PS700

DS21760F-page 10

 2004 Microchip Technology Inc.

3.4

SMBus/I2C Interface

The PS700 supports a 2-wire bidirectional bus and

data transmission protocol that is fully compatible with

the industry standard SMBus V1.1 based on the I2C

interface. This interface is used to read and write data

from/to the on-chip registers and EEPROM. The device

responds to the same SMBus slave address for access

to all functions. The following is a brief overview of the

SMBus/I2C operational implementation in the PS700.

Please refer to the SMBus v1.1 specification for

complete operational details of this industry standard

interface. This specification can be obtained at the

SMBus

Implementer’s

Forum

web

site

www.smbus.org.

3.4.1

SMBus OVERVIEW

SMBus is a two-wire multi-master bus, meaning that

more than one device capable of controlling the bus

can be connected to it. A master device initiates a bus

transfer and provides the clock signals. A slave device

can receive data provided by the master or can in

return provide data to the master.

Since more than one device may attempt to take

control of the bus as a master, SMBus provides an

arbitration mechanism based on I2C and relying on the

wired-AND connection of all SMBus devices residing

on the bus. If two or more masters try to place informa-

tion on the bus, the first to produce a “one” when the

other(s) produce a “zero” loses arbitration and has to

release the bus.

The clock signals during arbitration are a wired-AND

combination of all the clocks provided by SMBus

masters. Bus clock signals from a master can only be

altered by clock stretching or by other masters and only

during a bus arbitration situation. In addition to bus

arbitration, SMBus implements the I2C method of clock

low extending in order to accommodate devices of

different speeds on the same bus.

SMBus version 1.1 can be implemented at any voltage

between 3 and 5 Volts ±10%. Devices can be powered

by the bus VDD or by their own power source (such as

Smart Batteries) and they will interoperate flawlessly as

long

they

adhere

the

SMBus

electrical

specifications.

3.4.2

SMBus DATA TRANSFERS

A device that sends data onto the SMBus is defined as

a transmitter and a device receiving data as a receiver.

The device that controls the message is called a

“master”. The devices that are controlled by the master

are “slaves”. The SMBus must be controlled by a

master device that generates the serial clock (SCL),

controls the bus access and generates Start and Stop

conditions. The PS700 operates as a slave on the two-

wire bus. Connections to the bus are made via the

open-drain I/O lines SDA and SCL.

SMBus operates according to the following bus

protocol:

• Data transfer may be initiated only when the bus

is not busy.

• During data transfer, the data line must remain

stable whenever the clock line is high. Changes in

the data line while the clock line is high will be

interpreted as control signals.

The SMBus specification defines the following bus

conditions:

Bus Not Busy: Both data and clock lines remain high.

Start Data Transfer: A change in the state of the data

line from high to low, while the clock is high, defines a

Start condition.

Stop Data Transfer: A change in the state of the data

line from low to high, while the clock line is high, defines

the Stop condition.

Data Valid: The state of the data line represents valid

data when, after a Start condition, the data line is stable

for the duration of the high period of the clock signal.

The data on the line must be changed during the low

period of the clock signal. There is one clock pulse per

bit of data. Each data transfer is initiated with a Start

condition and terminated with a Stop condition. The

number of data bytes transferred between Start and

Stop conditions is not limited and is determined by the

master device. The information is transferred byte-wise

and each receiver Acknowledges with a ninth bit.

Acknowledge:

Each

receiving

device,

when

addressed, is obliged to generate an Acknowledge bit

after the reception of each byte. The master device

must generate an extra clock pulse which is associated

with this Acknowledge bit.

A device that Acknowledges must pull down the SDA

line during the Acknowledge clock pulse in such a way

that the SDA line is stable low during the high period of

the Acknowledge related clock pulse. Of course, setup

and hold times must be taken into account. A master

must signal an end of data to the slave by not generat-

ing an Acknowledge bit on the last byte that has been

clocked out of the slave. In this case, the slave must

leave the data line high to enable the master to

generate the Stop condition.

PS700 Datasheet(PDF) 10 Page - Microchip Technology

PS700 Datasheet(HTML) 10 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38

Datasheet Descarga

Enlace URL