K8DT-AS

13

Recommended Ferrules and Tools

Recommended ferrules

Note: 1. Make sure that the outer diameter of the wire coating is

smaller than the inner diameter of the insulation sleeve of

the recommended ferrule.

2. Make sure that the ferrule processing dimensions conform

to the following figures.

Recommended Flat-blade Screwdriver

Use a flat-blade screwdriver to connect and remove wires.

Use the flat-blade screwdriver.

The following table shows manufacturers and models as of 2015/Dec.

* OMRON's exclusive purchase model XW4Z-00B is available to

order as SZF 0-0.4

×2.5 (manufactured by Phoenix Contact).

• Refer to the contents of this datasheet for cable selection and other

conditions for compliance with EMC standards.

Precaution on EN Standard Compliance

The K8DT complies with EN 60947-5-1 when it is built into a panel,

but observe the following handling methods to ensure compliance

with the requirements of this standard.

Wiring

Overvoltage category III

Pollution degree 2

• Open-frame Device

• If basic, double, or reinforced insulation is required, use the basic,

double, or reinforced insulation defined in IEC 60664 that is

suitable for the maximum applied voltage for the clearance, solid

insulation, and other factors.

• There is basic insulation between the power supply terminals and

input terminals.

• There is basic insulation between the power supply terminals and

output terminals.

• There is basic insulation between the input terminals and output

terminals.

• Operating section must have reinforced or double insulation.

• The sides of the case are not isolated.

• Connect the output contacts (contacts with different polarity) so

that they reach the same potential.

Applicable

wire

Ferrule

Conductor

Length

(mm)

Stripping

length

(mm)

(Ferrules

used)

Recommended ferrules

(mm2) (AWG)

PhoenixContact

product

Weidmuller

product

Wago product

0.25

24

8

10

AI 0.25-8

H0.25/12

FE-0.25-8N-YE

10

12

AI 0.25-10

---

---

0.34

22

8

10

AI 0.34-8

H0.34/12

FE-0.34-8N-TQ

10

12

AI 0.34-10

---

---

0.5

20

8

10

AI 0.5-8

H0.5/14

FE-0.5-8N-WH

10

12

AI 0.5-10

H0.5/16

FE-0.5-10N-WH

0.75

18

8

10

AI 0.75-8

H0.75/14

FE-0.75-8N-GY

10

12

AI 0.75-10

H0.75/16

FE-0.75-10N-GY

1/1.25

18/17

8

10

AI 1-8

H1.0/14

FE-1.0-8N-RD

10

12

AI 1-10

H1.0/16

FE-1.0-10N-RD

1.25/1.5

17/16

8

10

AI 1.5-8

H1.5/14

FE-1.5-8N-BK

10

12

AI 1.5-10

H1.5/16

FE-1.5-10N-BK

Recommended crimp tool

CRIMPFOX6

CRIMPFOX6T-F

CRIMPFOX10S

PZ6 roto

Variocrimp4

Model

Manufacturer

ESD0.40

×2.5

Wera

SZS 0.4

×2.5

SZF 0-0.4

×2.5 *

Phoenix Contact

0.4

×2.5×75 302

Wiha

AEF.2.5

×75

Facom

210-719

Wago

SDI 0.4

×2.5×75

Weidmuller

8 to 10 mm

1.9 mm max.

2.6 mm max.

Side

0.4 mm

2.5 mm dia.

2.5 mm

Front

EN/IEC Standard Compliance

Not isolated

Reinforced insulation

(Double insulation)