PIC16F753 datasheet(25/230 Pages) MICROCHIP

25 / 230 page

 2013-2015 Microchip Technology Inc.

DS40001709C-page 25

PIC16F753/HV753

3.0

FLASH PROGRAM MEMORY

SELF READ/SELF WRITE

CONTROL

The Flash program memory is readable and writable

during normal operation (full VDD range). This memory

is not directly mapped in the register file space.

Instead, it is indirectly addressed through the Special

Function Registers (see Registers 3-1 to 3-5). There

are six SFRs used to read and write this memory:

•PMCON1

•PMCON2

•PMDATL

•PMDATH

• PMADRL

• PMADRH

When interfacing the program memory block, the

PMDATL and PMDATH registers form a two-byte word

which holds the 14-bit data for read/write, and the

PMADRL and PMADRH registers form a two-byte

word which holds the 10-bit address of the Flash loca-

tion being accessed. These devices have 1K words of

program Flash with an address range from 0000h to

03FFh.

The program memory allows a single-word read and a

four-word write. A four-word write automatically erases

the row of the location and writes the new data (erase

before write).

The write time is controlled by an on-chip timer. The

write/erase voltages are generated by an on-chip

charge pump rated to operate over the voltage range

of the device for byte or word operations.

When the device is code-protected, the CPU may

continue to read and write the Flash program memory.

Depending on the settings of the Flash Program

Memory Enable (WRT<1:0>) bits, the device may or

may not be able to write certain blocks of the program

memory; however, reads of the program memory are

allowed.

When the Flash program memory Code Protection

(CP) bit in the Configuration Word register is enabled,

the program memory is code-protected, and the

device programmer (ICSP™) cannot access data or

program memory.

3.1

PMADRH and PMADRL Registers

The PMADRH and PMADRL registers can address up

to a maximum of 1K words of program memory.

When selecting a program address value, the Most

Significant Byte (MSB) of the address is written to the

PMADRH register and the Least Significant Byte

(LSB) is written to the PMADRL register.

3.2

PMCON1 and PMCON2 Registers

PMCON1 is the control register for the data program

memory accesses.

Control bits RD and WR initiate read and write,

respectively. These bits cannot be cleared, only set in

software. They are cleared in hardware at completion

of the read or write operation. The inability to clear the

WR bit in software prevents the accidental premature

termination of a write operation.

The WREN bit, when set, will allow a write operation.

On power-up, the WREN bit is clear.

PMCON2 is not a physical register. Reading PMCON2

will read all ‘0’s. The PMCON2 register is used

exclusively in the Flash memory write sequence.

PIC16F753 Datasheet(PDF) 25 Page - Microchip Technology

PIC16F753 Datasheet(HTML) 25 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL