GAL16V8D-25LS datasheet(11/24 Pages) LATTICE

11 / 24 page

Specifications GAL16V8D

VIL

Input Low Voltage

Vss – 0.5

—

0.8

VIH

Input High Voltage

2.0

—

Vcc+1

IIL1

Input or I/O Low Leakage Current

0V ≤ VIN ≤ VIL (MAX.)

—

–100

μA

IIH

Input or I/O High Leakage Current

3.5V ≤ VIN ≤ VCC

——

μA

VOL

Output Low Voltage

IOL = MAX. Vin = VIL or VIH

—

0.5

VOH

Output High Voltage

IOH = MAX. Vin = VIL or VIH

2.4

—

IOL

Low Level Output Current

L-3/-5 & -7 (Ind. PLCC)

—

L-7 (Except Ind. PLCC)/-10/-15/-25

—

Q-10/-15/-20/-25

IOH

High Level Output Current

—

–3.2

IOS2

Output Short Circuit Current

VCC = 5V

VOUT = 0.5V T

A= 25°C

–30

—

–150

Recommended Operating Conditions

Commercial Devices:

Ambient Temperature (T

A) ............................... 0 to 75°C

Supply voltage (V

CC)

with Respect to Ground ..................... +4.75 to +5.25V

Industrial Devices:

Ambient Temperature (T

A) ........................... –40 to 85°C

Supply voltage (V

CC)

with Respect to Ground ..................... +4.50 to +5.50V

Absolute Maximum Ratings(1)

Supply voltage V

CC ...................................... –0.5 to +7V

Input voltage applied .......................... –2.5 to V

CC +1.0V

Off-state output voltage applied ......... –2.5 to V

CC +1.0V

Storage Temperature ................................ –65 to 150°C

Ambient Temperature with

Power Applied ........................................ –55 to 125°C

1.Stresses above those listed under the “Absolute Maximum

Ratings” may cause permanent damage to the device. These

are stress only ratings and functional operation of the device at

these or at any other conditions above those indicated in the

operational sections of this specification is not implied (while

programming, follow the programming specifications).

DC Electrical Characteristics

Over Recommended Operating Conditions (Unless Otherwise Specified)

SYMBOL

PARAMETER

CONDITION

MIN.

TYP.3

MAX.

UNITS

COMMERCIAL

ICC

Operating Power

VIL = 0.5V VIH = 3.0V

L -3/-5/-7/-10

—

115

Supply Current

ftoggle = 15MHz Outputs Open

L-15/-25

—

Q-10/-15/-25

—

INDUSTRIAL

ICC

Operating Power

VIL = 0.5V VIH = 3.0V

L -7/-10/-15/-25

—

130

Supply Current

ftoggle = 15MHz Outputs Open

Q -20/-25

—

1) The leakage current is due to the internal pull-up resistor on all pins. See Input Buffer section for more information.

2) One output at a time for a maximum duration of one second. Vout = 0.5V was selected to avoid test problems caused by tester

ground degradation. Characterized but not 100% tested.

3) Typical values are at Vcc = 5V and TA = 25 °C

GAL16V8D-25LS Datasheet(PDF) 11 Page - Lattice Semiconductor

GAL16V8D-25LS Datasheet(HTML) 11 Page - Lattice Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Datasheet Descarga

Enlace URL