LT1952IGN datasheet(18/24 Pages) LINER

18 / 24 page

LT1952/LT1952-1

19521fd

VSS(t) = SS_MAXDC(DC) (1 – e(–t/RC))

to give:

t = RC • (–1) • ln(1 – VSS/SS_MAXDC(DC))

where:

VSS = SS_MAXDC voltage at time t

SS_MAXDC(DC) = programmed DC voltage setting

maximum duty cycle clamp =

VREF(RB/(RT + RB)

R = RCHARGE (Figure 11) = RT • RB/(RT + RB)

C = CSS (Figure 11)

Example (1) No Switching Period

Theperiodofnoswitchingfortheconverter,whenasoft-start

event has occurred, depends on how far SS_MAXDC can

fall before recharging occurs and how long a fault exists. It

will be assumed that a fault triggering soft-start is removed

before SS_MAXDC can reach its reset threshold (0.45V).

No Switching Period = tDISCHARGE + tCHARGE

tDISCHARGE = discharge time from SS_MAXDC(DC) to

0.45V

tCHARGE = charge time from 0.45V to VSS(ACTIVE)

tDISCHARGE was already calculated earlier as 185μs.

tCHARGE is calculated by assuming the following:

VREF = 2.5V, RT = 35.7k, RB = 100k, CSS = 0.1μF and

VSS(MIN) = 0.45V.

tCHARGE = t(VSS = 0.8V) – t(VSS = 0.45V)

Step 1:

SS_MAXDC(DC) = 2.5[100k/(35.7k + 100k)] = 1.84V

RCHARGE = (35.7k • 100k/135.7k) = 26.3k

Step 2:

t(VSS = 0.45V) is calculated from,

t = RCHARGE • CSS • (–1) • ln(1 – VSS/SS_MAXDC(DC))

= 2.63e4 • 1e–7 • (–1) • ln(1 – 0.45/1.84)

= 2.63e–3 • (–1) • ln(0.755) = 7.3e–4 s

APPLICATIONS INFORMATION

Step 3:

t(VSS = 0.8V) is calculated from:

t = RCHARGE • CSS • (–1) • ln(1 – VSS/SS_MAXDC(DC))

= 2.63e4 • 1e–7 • (–1) • ln(1 – 0.8/1.84)

= 2.63e–3 • (–1) • ln(0.565) = 1.5e–3 s

From Step 1 and Step 2:

tCHARGE = (1.5 – 0.73)e–3 s = 7.7e–4 s

The total time of no switching for the converter due to a

soft-start event:

= tDISCHARGE + tCHARGE = 1.85e–4 + 7.7e–4 = 9.55e–4 s

Example (2) Converter Output Rise Time

The rise time for the converter output to reach regulation

can be closely approximated as the time between the start

of switching (SS_MAXDC = VSS(ACTIVE))andthetimewhere

converter duty cycle is in regulation (DC(REG)) and no

longer controlled by SS_MAXDC (SS_MAXDC = VSS(REG)).

Converter output rise time can be expressed as:

Output Rise Time = t(VSS(REG)) – t(VSS(ACTIVE))

Step 1: Determine converter duty cycle DC(REG) for

output in regulation.

The natural duty cycle DC(REG) of the converter depends on

several factors. For this example it is assumed that DC(REG)

= 60% for system input voltage near the undervoltage

lockout threshold (UVLO). This gives SD_VSEC = 1.32V.

Also assume that the maximum duty cycle clamp

programmed for this condition is 72% for SS_MAXDC(DC)

= 1.84V, fOSC = 200kHz and RDELAY = 40k.

Step 2: Calculate VSS(REG)

TocalculatethelevelofSS_MAXDC(VSS(REG))thatnolonger

clamps the natural duty cycle of the converter, the equation

for maximum duty cycle clamp must be used (see previous

section ‘Programming Maximum Duty Cycle Clamp’).

The point where the maximum duty cycle clamp meets

DC(REG) during soft-start is given by:

DC(REG) = Max Duty Cycle clamp

0.6 = k • 0.522(SS_MAXDC(DC)/SD_VSEC) –

(tDELAY • fOSC)

LT1952IGN Datasheet(PDF) 18 Page - Linear Technology

LT1952IGN Datasheet(HTML) 18 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Datasheet Descarga

Enlace URL