ATmega169P datasheet(62/393 Pages) ATMEL

62 / 393 page

8018N–AVR–08/09

ATmega169P

12.2

12.2.1

EICRA – External Interrupt Control Register A

The External Interrupt Control Register A contains control bits for interrupt sense control.

• Bit 1, 0 – ISC01, ISC00: Interrupt Sense Control 0 Bit 1 and Bit 0

The External Interrupt 0 is activated by the external pin INT0 if the SREG I-flag and the corre-

sponding interrupt mask are set. The level and edges on the external INT0 pin that activate the

interrupt are defined in Table 12-1. The value on the INT0 pin is sampled before detecting

edges. If edge or toggle interrupt is selected, pulses that last longer than one clock period will

generate an interrupt. Shorter pulses are not guaranteed to generate an interrupt. If low level

interrupt is selected, the low level must be held until the completion of the currently executing

instruction to generate an interrupt.

12.2.2

EIMSK – External Interrupt Mask Register

• Bit 7 – PCIE1: Pin Change Interrupt Enable 1

When the PCIE1 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), pin

change interrupt 1 is enabled. Any change on any enabled PCINT15..8 pin will cause an inter-

rupt. The corresponding interrupt of Pin Change Interrupt Request is executed from the PCI1

Interrupt Vector. PCINT15:8 pins are enabled individually by the PCMSK1 Register.

• Bit 6 – PCIE0: Pin Change Interrupt Enable 0

When the PCIE0 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), pin

change interrupt 0 is enabled. Any change on any enabled PCINT7..0 pin will cause an interrupt.

The corresponding interrupt of Pin Change Interrupt Request is executed from the PCI0 Inter-

rupt Vector. PCINT7:0 pins are enabled individually by the PCMSK0 Register.

• Bit 0 – INT0: External Interrupt Request 0 Enable

When the INT0 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), the exter-

nal pin interrupt is enabled. The Interrupt Sense Control0 bits 1/0 (ISC01 and ISC00) in the

External Interrupt Control Register A (EICRA) define whether the external interrupt is activated

on rising and/or falling edge of the INT0 pin or level sensed. Activity on the pin will cause an

Bit

765

432

(0x69)

–

ISC01

ISC00

EICRA

Read/Write

RRR

R/W

Initial Value

Table 12-1.

Interrupt 0 Sense Control

ISC01

ISC00

Description

The low level of INT0 generates an interrupt request.

Any logical change on INT0 generates an interrupt request.

The falling edge of INT0 generates an interrupt request.

The rising edge of INT0 generates an interrupt request.

Bit

543

210

0x1D (0x3D)

PCIE1

PCIE0

–

–INT0

EIMSK

Read/Write

R/W

Initial Value

ATmega169P Datasheet(PDF) 62 Page - ATMEL Corporation

ATmega169P Datasheet(HTML) 62 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL