Capacitor Hardware

CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com

Type VR Vertical Mounting Clamp

Type TH Horizontal Mounting Clip

Dimensions in Inches

Nominal Dia.

Catalog

of Part to be

Part Number

Mounted

A

B

C

TH17

0.625

0.312 0.720 0.015

TH25

1.375

0.312 1.500 0.030

CDE VR mounting clamps may be

used to mount any cylindrical ca-

pacitor with a 1” to 3” diameter

that is to be mounted in a verti-

cal position. Material is 1010 CRS,

commercial grade #4 temper ASI

scale. Parts are finished with .0001

(nominal) zinc chromate plating.

Use for mounting CG types, PSU, SF

and MPF types. Material thickness

is .035”

Catalog Part Number

Dimensions

Diameter

Unassembled

Assembled

of Part to be

Without

Screw & Nut

with

A

B

C

Mounted

Screw & Nut

Included

Screw & Nut

1" to 1-1/16

VR1B

VR1

VR1A

1"

1-7/16"

1-7/8*"

1-3/8" to 1-7/16

VR3B

VR3

VR3A

1-3/8"

1-25/32"

2-7/32"

1-1/2" to 1-9/16

VR4B

VR4

VR4A

1-1/2"

1-15/16"

2-11/32"

1-3/4" to 1-13/16

VR6B

VR6

VR6A

1-3/4"

2-1/4"

2-9/16"

2" to 2-1/16

VR8B

VR8

VR8A

2"

2-1/2"

2-13/16"

2-1/2" to 2-9/16

VR10B

VR10

VR10A

2-1/2"

3"

3-5/16"

3" to 3-1/8

VR12B

VR12

VR12A

3"

3-7/16"

3-13/16"

Screw

VRSCREW

—

—

9/16" long 6-32 thread NC-2A

Nut

VRNUT

—

—

Standard hex nut to fit screws

15K Ohm 2 watt bleeder resistors for AC motor start applica-

tions. Saves relay switch contacts and capacitor, particularly in

capacitor start applications. 1/4” quick connect terminals elimi-

nate need for soldering.

ACR15K:

Pack of 10, 15K Ohm 2 watt bleeder resistor without quick con-

nect terminals.

220K Ohm 1 watt bleeder resistors for AC motor run applica-

tions. Saves relay switch contacts and capacitor, particularly in

capacitor run applications. 1/4” quick connect terminals elimi-

nate need for soldering.

ACR220K:

Pack of 10, 220K Ohm 1 watt bleeder resistor without quick con-

nect terminals.

These clips, though designed for

capacitors, have varied applica-

tions to retain many cylindrical

components. They are used ex-

tensively in the electrical and elec-

tronic industries to hold spindles,

condensers, capacitors, tubes,

rods and conduit. Clips have phos-

phate and oil finish.

Material thickness TH13 thru TH17

is .016”. TH21 thru TH25 is .020”

ACR220KT Motor Run Resistor Kit

ACR15KT Motor Start Resistor Kit

VR1, 3 & 4

VR6, 8,10 & 12

B Mtg

.219”

.375”

.156”

2 Holes

.1561” Dia.

.562” .750”

C ±0.01”

0.176” x 0.281”

±0.016 (3 places).

B Mtng ±0.03”

0.344”

±0.016”

0.188”

±0.016”

A ±0.016”

75 º

120 º ±3 º

(3 Places)

Ø 0.201” ±0.005”

B Mtng ±0.03”

0.375”±0.016”

0.075” ±0.016”

0.035”

1.125” ±0.016”

0.500” ±0.016”

Material Thickness

TH17 is 0.016”, TH25

is 0.025”.

Material: 1050 high

carbon steel with

phosphate and oil

finish. TH25 is 1060.

0.594"

(*)

B

A

0.135" Dia. Hole

(*) 0.340" except TH25 is 0.590".

Retaining tabs must

extend lower

than base of clip

C ±0.010"

Added tolerance to "C" dim.

(*) 0.340” execpt TH25 is 0.590”

Retaining tabs

must extend

lower than base

of clip

0.135” Dia. Hole