■Size List

■Specifications

■Dimensions

(unit : mm)

※1 Please reduce 0.25V per 1

°C from over 85°C for 25V products.

※2 In case of some problems for measured values, measure after applying rated voltage for 6.3 to 16 and 30V products or temperature

derating voltage for 25V products for 30 minutes at 105

°C.

RV : Rated voltage

(SV) : Surge (room temperature)

Size Code

A

B

C

D

E

F

4.0

5.0

6.3

6.3

8.0

10.0

φD＋0.5max. Lmax.

7.8

7.8

7.8

10.8

11.5

11.5

0.45

0.45

0.45

0.60

0.60

0.60

0.5

0.5

0.5

0.5

0.8

0.8

0.5

0.5

0.5

0.5

0.8

0.8

2.0

±0.5

2.0

±0.5

2.5

±0.5

2.5

±0.5

3.5

±0.5

5.0

±0.5

F

φd±0.05 Gmax.

Kmax.

（＋）

G

A'

C

A

B

B'

Standards of terminal lead position

Sleeve

φd

L

15min.

4min.

19min.

F

Mark

; ideal

terminal lead position C;

the middle point of A-A'

1.0

1.5

2.2

3.3

4.7

6.8

10

15

22

33

47

A

B

C

A

B

C

D

A

A

B

B

C

D

D

A

A

B

B

C

C

C

D

E

F

F

A

B

B

C

D

D

E

F

RV

µF

6.3

(7.2)

16

(18.4)

25

(25.0)

10

(11.5)

30

(34.5)

(SV)

-55

°C to +105°C

M :

±20%

Less than or equal to the value of Table13

Less than or equal to the value of Table13

Less than or equal to the value of Table13

-55

°C

+105

°C

∆C/C

tan

δ

Leakage current

∆C/C

tan

δ

Leakage current

∆C/C

tan

δ

Leakage current

0.75 to 1.25

0.75 to 1.25

Within

±20%

1.5 times or less than an initial standard

Below an initial standard

Within

±10%

1.5 times or less than an initial standard

Below an initial standard

Within

±5%

Below an initial standard

Below an initial standard (after voltage processing)

Items

Characteristics

Endurance

Damp heat (Steady state)

Resistance to

soldering heat

Characteristics of impedance

ratio at high temp. and low temp.

Conditions

Category temperature range

Tolerance on rated capacitance

Tangent of loss angle

Leakage current

ESR

120Hz

120Hz

105

°C, 2,000h, Rated

voltage applied

(25V

→20V applied) ※1

60

°C, 90 to 95%RH,

1,000h,

No-applied voltage

Flow method

(260

±5°C X 10s)

※2

Based the value at

100KHz

，+20

°C

After 2 minutes

42

Aluminum solid capacitors with Organic semiconductive electrolyte

Suitable for noise limiters and switching power supplies that

make a point of high frequency characteristics. Also, make

use of it when needed long life span and high reliability.

Standard radial lead type