| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
AMMC008AWP Datasheet(PDF) 22 Page - Advanced Micro Devices |
|
|
|||||||||||||||||||||||||||||
AMMC008AWP Datasheet(HTML) 22 Page - Advanced Micro Devices |
|
22 / 39 page ![]() 22 AmMC0XXA PR EL IMIN AR Y attempt to read the device will produce valid data on D7. The Data Polling feature is valid after the rising edge of the fourth WE# pulse of the four write pulse sequence. While the Embedded Erase algorithm is in operation, D7 will read “0” until the erase operation is completed. Upon completion of the erase operation, the data on D7 will read “1”. The Data Polling feature is only active during the Embedded Programming or Erase algorithms. Please note that D7 may change asynchronously while Output Enable (OE#) is asserted low. This means that the device is driving status information on D7 at one instant of time and then the byte’s valid data at the next instant of time. Depending on when the system samples the D7 output, it may read either the status or valid data. Even if the device has completed the Embedded oper- ation and D7 has a valid data, the data outputs on D0- D6 may be still invalid since the switching time for data bits (D0-D7) will not be the same. This happens since the internal delay paths for data bits (D0-D7) within the device are different. The valid data will be provided only after a certain time delay (>tOE). Please refer to Figure 9 for a detailed timing diagram. See Figure 6 for the Data Polling algorithm. Toggle Bit—D6 (D14 on Odd Byte) The toggle bit is used for entering the Erase Suspend mode. Refer to the previous section entitled “Sector Erase Suspend” and Table 15 for information on this bit. Table 15. Hardware Sequence Flags Notes: 1. Performing successive read operations from the erase-suspended sector will cause D2 to toggle. 2. Performing successive read operations from any address will cause D6 to toggle. 3. Reading the byte address being programmed while in the erase-suspend program mode will indicate logic “1” at the D2 bit. However, successive reads from the erase-suspended sector will cause D2 to toggle. BUSY# (RY/BY#—Ready/Busy) The BUSY# signal indicates to the host the status of operations within the Miniature Card. The BUSY# signal is tied to the components’ RY/BY# pins. The RY/BY# signal from AMD Flash devices in the Miniature Card indicate that the Embedded Algo- rithms are either in progress or have been completed. If the output is low, the device is busy with either a pro- gram or erase operation. If the output is high, the de- vice is ready to accept any read/write or erase operation. When the RY/BY# pin is low, the device will not accept any additional program or erase com- mands with the exception of the Erase Suspend com- mand. If a Flash device is placed in an Erase Suspend mode, the RY/BY# output will be high. Refer to the section “Sector Erase Suspend” for more information. During programming, the RY/BY# pin is driven low after the rising edge of the fourth WE# pulse. During an erase operation, the RY/BY# pin is driven low after the rising edge of the sixth WE# pulse. The RY/BY# pin should be ignored while RESET# is at VIL. Status D7 D6 D5 D3 D2 In Progress Byte Program in Embedded Program Algorithm D7 Toggle 0 0 1 Embedded Erase Algorithm 0 Toggle 0 1 Toggle Erase Suspended Mode Erase Suspend Read (Erase Suspended Sector) 11 00 Toggle (Note 1) Erase Suspend Read (Non-Erase Suspended Sector) Data Data Data Data Data Erase Suspend Program (Non-Erase Suspended Sector) D7 Toggle (Note 2) 01 1 (Note 3) Exceeded Time Limits Byte Program in Embedded Program Algorithm D7 Toggle 1 0 1 Program/Erase in Embedded Erase Algorithm 0 Toggle 1 1 N/A Erase Suspended Mode Erase Suspend Program (Non-Erase Suspended Sector) D7 Toggle 1 1 N/A |
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |