MAX4591ESE datasheet(4/12 Pages) MAXIM

4 / 12 page

High-Speed, Single-Supply,

Quad, SPST Analog Switches

_______________________________________________________________________________________

ELECTRICAL CHARACTERISTICS—Single +15V Supply

(V+ = +15V, V- = GND = 0, VINH = 5V, VINL = 0.8V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)

(Note 2)

Note 2: The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in

this data sheet.

Note 3: Guaranteed by design.

Note 4:

∆RON = ∆RON max - ∆RON min.

Note 5: Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the

specified analog signal range.

Note 6: Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at +25°C.

Note 7: Off-isolation = 20log10 [VCOM ⁄ (VNC or VNO)], VCOM = output, VNC or VNO = input to off switch.

Note 8: Between any two switches.

PARAMETER

SYMBOL

MIN

TYP

MAX

UNITS

Analog Signal Range

VCOM_,

VNO_,

VNC_

0V+

CONDITIONS

(Note 3)

On-Resistance

RON

Ω

ICOM_ = -10mA,

VNO_ or VNC_ = 10V

Turn-On Time

tON

VNO_ or VNC_ = 10V,

Figure 2

Break-Before-Make Time

Delay (Note 3)

520

MAX4593 only, RL = 300

Ω, CL = 35pF

Turn-Off Time

tOFF

VNO_ or VNC_ = 10V,

Figure 2

Negative Supply Current

I-

-1

0.001

µA

Positive Supply Current

I+

-1

0.001

µA

Charge Injection

(Note 3)

CL = 1nF, VGEN = 0,

RGEN = 0

Ω, Figure 4

On-Resistance Match

Between Channels (Notes 3, 4)

∆RON

0.5

1.5

Ω

ICOM_ = -10mA,

VNO_ or VNC_ = 10V

On-Resistance Flatness

(Notes 3, 5)

RFLAT(ON)

0.7

1.5

Ω

ICOM_ = -10mA;

VNO_ or VNC_ = 3V, 6V, 9V

NO_ or NC_ Off-Leakage

Current (Note 6)

INO_(OFF)

INC_(OFF)

-0.1

0.01

0.1

V+ = 15.5V;

VCOM_ = 14V, 1V;

VNO_ or VNC_ 1V, 14V

COM_ Off-Leakage Current

(Note 6)

ICOM_(OFF)

-0.1

0.01

0.1

V+ = 15.5V;

VCOM_ = 14V, 1V;

VNO_ or VNC_ = 1V, 14V

TA = +25°C

C, E

2.0

-5

C, E

-5

TA = +25°C

C, E

TA = +25°C

V+ = 15V, VIN_ = 0 or V+, all channels on or off

TA = +25°C

COM_ On-Leakage Current

(Note 6)

ICOM_(ON)

-0.2

0.02

0.2

V+ = 15.5V;

VCOM_ =14V, 1V;

VNO_ or VNC_ = 14V, 1V,

or floating

-10

C, E

ANALOG SWITCH

DYNAMIC

SUPPLY

MAX4591ESE Datasheet(PDF) 4 Page - Maxim Integrated Products

MAX4591ESE Datasheet(HTML) 4 Page - Maxim Integrated Products

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

Datasheet Descarga

Enlace URL