| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
MAX778LC/D Datasheet(PDF) 8 Page - Maxim Integrated Products |
|
|
|||||||||||||||||||||||||||||
MAX778LC/D Datasheet(HTML) 8 Page - Maxim Integrated Products |
|
8 / 12 page ![]() At heavy loads above approximately 100mA, the con- verter enters continuous-conduction mode, where cur- rent always flows in the inductor. The switch-on state is controlled cycle-by-cycle by either the maximum tON time or the switch’s preset current limit. As a result, the switch's current rating is not exceeded and the inductor is not saturated. At very heavy loads, the inductor cur- rent self-oscillates between this peak current limit and some lower value governed by the minimum off-time, the inductance value, and the input/output differential. With ILIM shorted to IN, the peak switch current of the internal NPN power switch is set to 1A. The peak switch current can be set to a lower value by connecting a resistor between ILIM and IN (see Current Limit sec- tion). This enables the use of physically smaller induc- tors with lower saturation-current ratings. At 1A, the switch voltage drop (VSW) is about 500mV. VSW decreases to about 250mV at 0.1A. Conventional PWM converters generate constant-fre- quency switching noise, while this architecture pro- duces variable-frequency switching noise. However, the noise does not exceed the current limit times the fil- ter-capacitor ESR, unlike conventional pulse-skippers. Step-Down Mode If the input voltage exceeds the output voltage, the MAX777L/MAX778L/MAX779L behave as “switched” linear regulators. If the output voltage starts to drop, the switch turns on and energy is stored in the coil, as in normal step-up mode. After the switch turns off, the voltage at LX flies high. The active rectifier turns on when LX rises above VIN. As in a linear regulator, the voltage difference between VIN and VOUT appears across the rectifier (actually a PNP transistor) until the current goes to zero and the rectifier turns off. At high VIN to VOUT differentials, the maximum load current is limited by the maximum allowable power dissipation in the package. For fully specified buck/boost converters, refer to the data sheet for the pin-compatible MAX877L/MAX878L/MAX879L. Active Rectifier The internal active rectifier of the MAX777L/MAX778L/ MAX779L replaces the external Schottky catch diode in normal boost operation. The rectifier consists of a PNP pass transistor and a unique control circuit which, in shutdown mode, entirely disconnects the load from the source. This is a distinct advantage over standard boost topologies, since it prevents battery drain in shut- down. The active rectifier also acts as a zero-dropout regulator if the input exceeds the regulated output. This allows the MAX777L/MAX778L/MAX779L to act as buck/boost converters. Useful in battery-powered applications, where the battery voltage may initially exceed the output voltage, the converters will regulate down to the output voltage and seamlessly switch into boost mode as the input drops below the output voltage. The pin-compati- ble MAX877L/MAX878L/MAX879L are fully specified buck/boost converters with higher specified output cur- rents than the MAX777L/MAX778L/MAX779L. Shutdown Shutdown ( SHDN) is a high-impedance, active-low input. Connect SHDN to VIN for normal operation. Keeping SHDN at ground holds the converters in shut- down mode. Since the active rectifier is turned off in shutdown mode, the path from input to load is cut, and the output effectively drops to 0V. The supply current in the shutdown state ranges from 4µA at VIN = 1V to 50µA at VIN = 4.5V. The shutdown circuit threshold is set nominally to VIN/2 + 250mV. When SHDN is below this threshold, the device is shut down and is enabled with SHDN above the threshold. When driven from external logic, SHDN can be driven to a higher voltage than VIN. Current Limit Connecting ILIM to IN sets an LX current limit of 1A. For smaller output power levels that do not require the max- imum peak current, the peak inductor current can be reduced to optimize overall efficiency and to allow very small, low-cost coils with lower current ratings. See also the Inductor Selection section. Reduce the MAX777L/MAX778L/MAX779L peak induc- tor current by connecting a resistor between ILIM and IN. See Figure 2 to select the resistor. Low-Voltage Input, 3V/3.3V/5V/ Adjustable Output, Step-Up DC-DC Converters 8 _______________________________________________________________________________________ 600 0 28 CURRENT-LIMIT RESISTOR vs. PEAK INDUCTOR CURRENT 800 RESISTOR VALUE (k Ω) 1000 1200 46 400 0 200 12 14 10 VIN = 2.5V Figure 2. Current-Limit Resistor vs. Current Limit |
|
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |