 |
Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
|
Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
SM5904CF Datasheet(PDF) 21 Page - Nippon Precision Circuits Inc |
|
|
|||||||||||||||||||||||||||||
SM5904CF Datasheet(HTML) 21 Page - Nippon Precision Circuits Inc |
|
|
21 / 35 page  NIPPON PRECISION CIRCUITS-21 SM5904CF 86H (digital audio interface settings) - CP1, CP2 (channel status and clock accuracy set- ting) When 0 and 0: Level 2 (max ± 300 ppm) When 0 and 1: Level 3 (max ± 10%) When 1 and 0: Level 1 (max ± 50 ppm) When 1 and 1: Not supported - LBIT (digital audio signal generation logic) When 1: Not assigned When 0: Post-recording software - DIT (digital audio interface enable) When 1: DIT output enable When 0: DIT LOW-level output 87H (subcode Q data setting) - QAD3 to QAD0 (Q data setting and word address specification) QAD3 (MSB) to QAD0 (LSB) specify one of 10 valid addresses in the range 0000 to 1001. If an address in the range 1010 to 1111 is speci- fied, the data on QD7 to QD0 is ignored. Note that writing to address 1001 also functions as the write stop command. - QD7 to QD0 (Q data setting and word data) The CD Q-channel has the general data format shown below. The write data required to fully specify the Q data is the 80 bits comprising CONTROL, ADR, and DATA-Q. The CRC write data is not required because it is generated by recalculation. Control 0123456789 78 79 80 95 S0, S1 ADR DATA-Q CRC S0, S1 96 bit 80 bit bit QAD3 QAD2 QAD1 QAD0 QD7 QD6 QD5 QD4 QD3 QD2 QD1 QD0 0 0 0 0 CTL0 CTL1 CTL2 CTL3 ADR3 ADR2 ADR1 ADR0 0 0 0 1 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 0 0 1 0 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 DQ16 0 0 1 1 DQ17 DQ18 DQ19 DQ20 DQ21 DQ22 DQ23 DQ24 0 1 0 0 DQ25 DQ26 DQ27 DQ28 DQ29 DQ30 DQ31 DQ32 0 1 0 1 DQ33 DQ34 DQ35 DQ36 DQ37 DQ38 DQ39 DQ40 0 1 1 0 DQ41 DQ42 DQ43 DQ44 DQ45 DQ46 DQ47 DQ48 0 1 1 1 DQ49 DQ50 DQ51 DQ52 DQ53 DQ54 DQ55 DQ56 1 0 0 0 DQ57 DQ58 DQ59 DQ60 DQ61 DQ62 DQ63 DQ64 1 0 0 1 DQ65 DQ66 DQ67 DQ68 DQ69 DQ70 DQ71 DQ72 Adderss map for Q data setting beuffer - Subcode Q data setting process Initially, data is written to word address range 0000 to 1000, and then data is written to address 1001. Next, only data that needs to be changed is written if the 91H command QRDY bit is 1, and then address 1001 is written again. Note that when shockproof mode is ON, the Q data is specified according to the data output from the SM5904CF. |
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Mexican ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
