| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
M37516 Datasheet(PDF) 21 Page - Mitsubishi Electric Semiconductor |
|
|
|||||||||||||||||||||||||||||
M37516 Datasheet(HTML) 21 Page - Mitsubishi Electric Semiconductor |
|
21 / 54 page ![]() 21/54 M37516M6-XXXHP GNOK-M37516M6-XXXHP-50 (MSETSU 2) PA GE qSerial I/O2 The serial I/O2 can be operated only as the clock synchronous type. As a synchronous clock for serial transfer, either internal clock or external clock can be selected by the serial I/O2 synchronous clock selection bit (b6) of serial I/O2 control register 1. The internal clock incorporates a dedicated divider and permits selecting 6 types of clock by the internal synchronous clock selec- tion bit (b2, b1, b0) of serial I/O2 control register 1. Regarding SOUT2 and SCLK2 being output pins, either CMOS output format or N-channel open-drain output format can be selected by the P01/SOUT2, P02/SCLK2 P-channel output disable bit (b7) of serial I/O2 control register 1. When the internal clock has been selected, a transfer starts by a write signal to the serial I/O2 register (address 001716). After comple- tion of data transfer, the level of the SOUT2 pin goes to high imped- ance automatically but bit 7 of the serial I/O2 control register 2 is not set to "1" automatically. When the external clock has been selected, the contents of the serial I/O2 register is continuously sifted while transfer clocks are input. Accordingly, control the clock externally. Note that the SOUT2 pin does not go to high impedance after completion of data trans- fer. To cause the SOUT2 pin to go to high impedance in the case where the external clock is selected, set bit 7 of the serial I/O2 control register 2 to "1" when SCLK2 is "H" after completion of data transfer. After the next data transfer is started (the transfer clock falls), bit 7 of the serial I/O2 control register 2 is set to "0" and the SOUT2 pin is put into the active state. Regardless of the internal clock to external clock, the interrupt re- quest bit is set after the number of bits (1 to 8 bits) selected by the optional transfer bit is transferred. In case of a fractional number of bits less than 8 bits as the last data, the received data to be stored in the serial I/O2 register becomes a fractional number of bits close to MSB if the transfer direction selection bit of serial I/O2 control register 1 is LSB first, or a fractional number of bits close to LSB if the said bit is MSB first. For the remaining bits, the previously re- ceived data is shifted. At transmit operation using the clock synchronous serial I/O, the SCMP2 signal can be output by comparing the state of the transmit pin SOUT2 with the state of the receive pin SIN2 in synchronization with a rise of the transfer clock. If the output level of the SOUT2 pin is equal to the input level to the SIN2 pin, "L" is output from the SCMP2 pin. If not, "H" is output. At this time, an INT2 interrupt request can also be generated. Select a valid edge by bit 2 of the interrupt edge selection register (address 003A16). [Serial I/O2 Control Registers 1, 2] SIO2CON1 / SIO2CON2 The serial I/O2 control registers 1 and 2 are containing various se- lection bits for serial I/O2 control as shown in Figure 19. Fig. 19 Structure of Serial I/O2 control registers 1, 2 Serial I/O2 control register 1 (SIO2CON1 : address 001516) Serial I/O2 control register 2 (SIO2CON2 : address 001616) b7 b7 b0 Optional transfer bits b2 b1 b0 0 0 0: 1 bit 0 0 1: 2 bit 0 1 0: 3 bit 0 1 1: 4 bit 1 0 0: 5 bit 1 0 1: 6 bit 1 1 0: 7 bit 1 1 1: 8 bit Not used ( returns "0" when read) Serial I/O2 I/O comparison signal control bit 0: P43 I/O 1: SCMP2 output SOUT2 pin control bit (P01) 0: Output active 1: Output high-impedance Internal synchronous clock selection bit b2 b1 b0 0 0 0: f(XIN)/8 (f(XCIN)/8 in low-speed mode) 0 0 1: f(XIN)/16 (f(XCIN)/16 in low-speed mode) 0 1 0: f(XIN)/32 (f(XCIN)/32 in low-speed mode) 0 1 1: f(XIN)/64 (f(XCIN)/64 in low-speed mode) 1 1 0: f(XIN)/128 f(XCIN)/128 in low-speed mode) 1 1 1: f(XIN)/256 (f(XCIN)/256 in low-speed mode) Serial I/O2 port selection bit 0: I/O port 1: SOUT2,SCLK2 output pin SRDY2 output enable bit 0: P03 pin is normal I/O pin 1: P03 pin is SRDY2 output pin Transfer direction selection bit 0: LSB first 1: MSB first Serial I/O2 synchronous clock selection bit 0: External clock 1: Internal clock P01/SOUT2 ,P02/SCLK2 P-channel output disable bit 0: CMOS output (in output mode) 1: N-channel open-drain output (in output mode ) b0 |
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |