PI3CH401LEX datasheet(3/6 Pages) PERICOM

3 / 6 page

|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||

||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||

2015-07-0017

PT0472-3

08/05/15

PI3CH401

4-Bit Bus Switch, Enable High

1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug

1.8V supply (Over operating range, TA = -40 ~ +85ºC, VCC=1.8V±10%, unless otherwise noted)

Symbol

Description

Test Conditions

(1)

Min

Typ

(2)

Max

Unit

VIH

Control Input HIGH Voltage

Guaranteed Logic HIGH Level

1.2

VCC+0.3

VIL

Control Input LOW Voltage

Guaranteed Logic LOW Level

-0.3

0.6

VIK

Clamp Diode Voltage

VCC = Min., IIN = -18mA

-0.7

-1.8

IIH

Input HIGH Current

VCC = Max., VIN = VCC

±1

μA

IIL

Input Low Current

VCC = Max., VIN = GND

±1

μA

IOZH

High-Impedance Current

0 ≤ A, B ≤ V

±1

μA

RON

Switch On-Resistance

(3)

VCC = Min., VIN = 0.0V

ION = -48mA

Ω

VCC = Min., VIN = 1.6V

ION = -15mA

Notes:

1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.

2. Typical values are at VCC = 1.8V, TA = 25°C ambient and maximum loading.

3. Measured by the voltage drop between A and B pin at indicated current through the switch. On-Resistance is determined

by the lower of the voltages on the two (Ax, Bx) pins.

Capacitance (TA = 25ºC, f=1MHz)

Symbol

(1)

Description

Test Conditions

Typ

(2)

Unit

CIN

Input Capacitance

VIN = 0V

2.0

COFF

A/B Capacitance, Switch Off

3.5

CON

A/B Capacitance, Switch On

7.0

Note:

1. These parameters are determined by device characterization but are not production tested

Power Supply Characteristics

Symbol

Description

Test Conditions

(1)

Min

Typ

Max

Unit

ICC

Quiescent Power Supply Current

VCC = 3.6V, VIN = GND or VCC

0.2

0.5

Note:

1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device.

2. Typical values are at +25°C ambient

Dynamic Electrical Characteristics

(Over Operating Range, TA = -40 ~ +85ºC, VCC=3.3V±10%)

Symbol

Description

Test Conditions

Min

Typ

Max

Unit

XTALK

Crosstalk

10MHz

-60

OIRR

Off-Isolation

10MHz

-60

-3dB Bandwidth

See test Diagram

500

MHz

Switch Characteristics

Over 3.3V Operating Range

Symbol

Description

Test Conditions

(1)

Min

Typ

Max

Unit

tPLH, tPHL

Propagation Delay

(2, 3) Ax to Bx, Bx to Ax

See test Diagram

0.3

tPZH, tPZL

Enable Time ENx to Ax or Bx

See test Diagram

1.5

9.0

tPHZ, tPLZ

Disable Time ENx to Ax or Bx

See test Diagram

1.5

9.0

PI3CH401LEX Datasheet(PDF) 3 Page - Pericom Semiconductor Corporation

PI3CH401LEX Datasheet(HTML) 3 Page - Pericom Semiconductor Corporation

Html Pages

1 2 3 4 5 6

Datasheet Descarga

Enlace URL