PI3CH480QEX datasheet(4/8 Pages) PERICOM

4 / 8 page

|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||

||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||

2015-07-0019

PT0476-3

08/05/15

PI3CH480

4-Channel 2:1 Mux/DeMux, Enable Low

1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug

Note:

1. See test circuit and waveforms.

2. This parameter is guaranteed but not tested on Propagation Delays.

3. The switch contributes no propagation delay other than the RC delay of the On-Resistance of the switch and the load capacitance. The

time constant for the switch alone is of the order of 0.30ns for 10pF load. Since this time constant is much smaller than the rise/fall

times of typical driving signals, it adds very little propagation delay to the system. Propagation delay of the switch when used in a

system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side.

Over 2.5V Operating Range

Symbol

Description

Test Conditions

(1)

Min

Typ

Max

Unit

tPLH, tPHL

Propagation Delay

(2, 3) Y to In, In to Y

See test Diagram

0.3

tPZH, tPZL

Enable Time S or EN to Y or In

See test Diagram

1.5

15.0

tPHZ, tPLZ

Disable Time S or EN to Y or In

See test Diagram

1.5

12.0

Note:

1. See test circuit and waveforms.

2. This parameter is guaranteed but not tested on Propagation Delays.

3. The switch contributes no propagation delay other than the RC delay of the On-Resistance of the switch and the load capacitance. The

time constant for the switch alone is of the order of 0.30ns for 10pF load. Since this time constant is much smaller than the rise/fall

times of typical driving signals, it adds very little propagation delay to the system. Propagation delay of the switch when used in a

system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side.

Over 1.8V Operating Range

Symbol

Description

Test Conditions

(1)

Min

Typ

Max

Unit

tPLH, tPHL

Propagation Delay

(2, 3) Y to In, In to Y

See test Diagram

0.3

tPZH, tPZL

Enable Time S or EN to Y or In

See test Diagram

1.5

25.0

tPHZ, tPLZ

Disable Time S or EN to Y or In

See test Diagram

1.5

12.0

Note:

1. See test circuit and waveforms.

2. This parameter is guaranteed but not tested on Propagation Delays.

3. The switch contributes no propagation delay other than the RC delay of the On-Resistance of the switch and the load capacitance. The

time constant for the switch alone is of the order of 0.30ns for 10pF load. Since this time constant is much smaller than the rise/fall

times of typical driving signals, it adds very little propagation delay to the system. Propagation delay of the switch when used in a

system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side.

Test Circuit for Electrical Characteristics

Notes:

1. CL = Load capacitance: includes jig and probe capacitance.

2. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator

3. All input impulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50-ohm, tR ≤ 2.5ns, tF ≤ 2.5ns.

4. The outputs are measured one at a time with one transition per measurement.

D.U.T

Pulse

Generator

VIN

VCC

VOUT

10pF

200Ω

6.0V

PI3CH480QEX Datasheet(PDF) 4 Page - Pericom Semiconductor Corporation

PI3CH480QEX Datasheet(HTML) 4 Page - Pericom Semiconductor Corporation

Html Pages

1 2 3 4 5 6 7 8

Datasheet Descarga

Enlace URL