| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
TMP320F2810PBKA Datasheet(PDF) 59 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
TMP320F2810PBKA Datasheet(HTML) 59 Page - Texas Instruments |
|
59 / 103 page ![]() TMS320F2810, TMS320F2812 DIGITAL SIGNAL PROCESSORS SPRS174B – APRIL 2001 – REVISED SEPTEMBER 2001 59 POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251–1443 32-bit CPU-Timers 0/1/2 (continued) Table 48. TIMERxTCR Register Bit Definitions† BIT NAME R/W RESET DESCRIPTION 15 TIF R/W=1 0 Timer Interrupt Flag. This flag gets set when the timer decrements to zero. This bit can be cleared by software writing a 1, but it can only be set by the timer reaching zero. Writing a 1 to this bit will clear it, writing a zero has no effect. 14 TIE R/W 0 Timer Interrupt Enable. If the timer decrements to zero, and this bit is set, the timer will assert its interrupt request. 13:12 Reserved R 0 Reserved 11 FREE R/W 0 Timer Emulation Modes: These bits are special emulation bits that determine the state of the timer when a breakpoint is encountered in the high-level language debugger. If the FREE bit is set to 1, then, upon a software breakpoint, the timer continues to run (that is, free runs). In this case, SOFT is a don’t care. But if FREE is 0, then SOFT takes effect. In this case, if SOFT = 0, the timer halts the next time the TIMH:TIM decrements. If the SOFT bit is 1, then the timer halts when the TIMH:TIM has decremented to zero. FREE SOFT Timer Emulation Mode 10 SOFT R/W 0 FREE SOFT Timer Emulation Mode 0 0 Stop after the next decrement of the TIMH:TIM (hard stop) 0 1 Stop after the TIMH:TIM decrements to 0 (soft stop) 1 0 Free run 1 1 Free run Note: That in the SOFT STOP mode, the timer will generate an interrupt before shutting down (since reaching 0 is the interrupt causing condition). 9:6 Reserved R/W 0 Reserved 5 TRB W/R=0 0 Timer Reload bit. When you write a 1 to TRB, the TIMH:TIM is loaded with the value in the PRDH:PRD, and the prescaler counter (PSCH:PSC) is loaded with the value in the timer divide-down register (TDDRH:TDDR). The TRB bit is always read as zero. 4 TSS R/W 0 Timer stop status bit. TSS is a 1-bit flag that stops or starts the timer. To stop the timer, set TSS to 1. To start or restart the timer, set TSS to 0. At reset, TSS is cleared to 0 and the timer immediately starts. 3:0 Reserved R/W 0 Reserved † x = 0, 1, or 2 |
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |