ASX340CS datasheet(69/74 Pages) ONSEMI

69 / 74 page

ASX340CS_DS Rev. F Pub. 6/15 EN

©Semiconductor Components Industries, LLC, 2015.

ASX340CS: 1/4-Inch Color CMOS NTSC/PAL Digital Image Sensor

Electrical Specifications

Two-Wire Serial Bus Timing

Figure 49 and Table 45 describe the timing for the two-wire serial interface.

Figure 49:

Two-Wire Serial Bus Timing Parameters

Notes:

1. This table is based on I2C standard (v2.1 January 2000). Philips Semiconductor.

2. Two-wire control is I2C-compatible.

3. All values referred to VIHmin = 0.9 VDD and VILmax = 0.1VDD levels. Sensor EXCLK = 27 MHz.

4. A device must internally provide a hold time of at least 300 ns for the SDATA signal to bridge the

undefined region of the falling edge of SCLK.

5. The maximum tHD;DAT has only to be met if the device does not stretch the LOW period (tLOW) of

the SCLK signal.

6. A Fast-mode I2C-bus device can be used in a Standard-mode I2C-bus system, but the requirement

tSU;DAT 250 ns must then be met. This will automatically be the case if the device does not stretch

the LOW period of the SCLK signal. If such a device does stretch the LOW period of the SCLK signal, it

Table 45:

Two-Wire Serial Bus Characteristics

fEXTCLK = 27 MHz; VDD = 1.8V; VDD_IO = 2.8V; VAA = 2.8V; VAA_PIX = 2.8V;

VDD_PLL = 2.8V; VDD_DAC = 2.8V; TA = 25°C

Parameter

Symbol

Standard-Mode

Fast-Mode

Unit

Min

Max

Min

Max

SCLK Clock Frequency

fSCL

0100

400

KHz

Hold time (repeated) START condition.

After this period, the first clock pulse is

generated

tHD;STA

4.0

0.6

s

LOW period of the SCLKclock

tLOW

4.7

1.3

s

HIGH period of the SCLKclock

tHIGH

4.0

0.6

s

Set-up time for a repeated START condition

tSU;STA

4.7

0.6

s

Data hold time

tHD;DAT

3.455

0.95

s

Data set-up time

tSU;DAT

250

1006

Rise time of both SDATA and SCLK signals

1000

20 + 0.1Cb7

300

Fall time of both SDATA and SCLK signals

300

20 + 0.1Cb7

300

Set-up time for STOP condition

tSU;STO

4.0

0.6

s

Bus free time between a STOP and START

condition

tBUF

4.7

1.3

s

Capacitive load for each bus line

400

Serial interface input pin capacitance

CIN_SI

3.3

SDATA max load capacitance

CLOAD_SD

SDATA pull-up resistor

RSD

1.5

4.7

1.5

4.7

K

tSU;STO

tSU;STA

tHD;STA

tHIGH

tLOW

tSU;DAT

tHD;DAT

SDATA

SCLK

tBUF

tHD;STA

ASX340CS Datasheet(PDF) 69 Page - ON Semiconductor

ASX340CS Datasheet(HTML) 69 Page - ON Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74

Datasheet Descarga

Enlace URL