PS60

PS60

PS60

Functions

●You can select switch working mode from the options shown in the table below.

（Note 1）In the Separate Mode, SW1 and SW2 work separately.

（Note 2）In the Window Comparator Mode, the minimum value for SW1 and SW2 corresponds to Setting 1 and the maximum value to Setting 2.

※ For how to set the switch output, see the description of the initial setting mode.

Switch working mode

●When you do not operate any buttons for about 10 seconds, the system will automatically select non-display mode and the LED indicator section will go off.

 Pressing any key will cause the LED indicator section to come on back again.

（Note 1）The decimal point shown in the figure on the right blinks during non-display mode.

（Note 2）Switch outputs and switch LEDs are operable even during non-display mode.

（Note 3）Error messages will appear during non-display mode.

※ For how to select non-display mode, see the description of the initial setting mode.

Non-display mode（Low power mode）

●You can select a conversion factor from the options shown in the table on the right.

（Note 1）Slashed box: No factors options are available due to inappropriate resolution

   

and the number of digits for display.

※ For how to set the conversion factor, see the description of the initial setting mode.

Conversion factor

●Two different digital filters（25ms and 250ms）are available.

 The digital filters are useful when it is hard to take readings due to too great fluctuations in pressure.

（Note 1）Any selected digital filter will be reflected on the pressure display and switch action.

※ For how to set the digital filter, see the description of the pressure setting mode.

Digital filter

All LED flash once.

The Operations Mode（pressule

detection）is activated.

Initial LED Display

Error Messages

■ If the following error messages are displayed, follow the procedures in the table:

2

Error message

Problem

Solution

Overload current.（Brinking of SW1 or SW2 indicates

excessive current on SW1 or SW2.）

Pressure detected when adjusting the zero point.

Applied pressure is higher than the maximum value

of the pressure display range.

Check the applied pressure.

Press the   button and reset the    display. Release the applied pressure

in the pressure port (opened to the atmosphere) and adjust the zero point again.

Disconnect the power, then check the load condition.

There are four operation modes. There are shown in the diagrams below.

Separate Mode

P1: Setting 1, P2: Setting 2, H: Hysteresis

Window Comparator Mode

（HI operation）

OFF

ON

-Pr

Pr

H

H

P1：SW1

P2：SW2

ON

OFF

-Pr

Pr

H

H

P1：SW1

P2：SW2

（LO operation）

（A operation）

OFF

ON

ON

-Pr

Pr

HH

P1

P2

P1

P2

（B operation）

OFF

OFF

ON

-Pr

Pr

HH

P1≦P2 or P1≧P2

P1≦P2−2H

Mode

Operation

SW1

Separate

H

○

○

L

○

○

A

○

○

B

○

○

H

○

○

L

○

○

A

○

○

B

○

○

Window Comparator

Setting 1

Minimum: Setting 1

Maximum: Setting 2

Minimum: Setting 1

Maximum: Setting 2

Setting 2

Separate Window Comparator

SW2

Output

Number

selected

Pressure range

103R

302R

102R

─

−0.10∼1.00

─

−1.0∼10.0

−14∼145

─

−100∼300

─

−75∼225

−1.00∼3.00

−14.5∼43.5

29.5∼0.0

(“-”symbol does not display)

−100∼100

─

−75∼75

−1.00∼1.00

−14.5∼14.5

29.5∼0.0

(“-”symbol does not display)

（kPa）

（MPa）

Ｐ１

Ｐ２

ｋＰａ

Ｐ１

Ｐ２

ｋＰａ

Ｐ１

Ｐ２

ｋＰａ