STM32F100XD datasheet(52/106 Pages) STMICROELECTRONICS

52 / 106 page

Electrical characteristics

STM32F100xC, STM32F100xD, STM32F100xE

52/106

DocID15081 Rev 10

Figure 13. Typical application with an 8 MHz crystal

1. REXT value depends on the crystal characteristics.

Low-speed external clock generated from a crystal/ceramic resonator

The low-speed external (LSE) clock can be supplied with a 32.768 kHz crystal/ceramic

resonator oscillator. All the information given in this paragraph are based on

characterization results obtained with typical external components specified in Table 23. In

the application, the resonator and the load capacitors have to be placed as close as

possible to the oscillator pins in order to minimize output distortion and startup stabilization

time. Refer to the crystal resonator manufacturer for more details on the resonator

characteristics (frequency, package, accuracy).

Note:

For CL1 and CL2 it is recommended to use high-quality ceramic capacitors in the 5 pF to

15 pF range selected to match the requirements of the crystal or resonator. CL1 and CL2, are

usually the same size. The crystal manufacturer typically specifies a load capacitance which

CL1

CL2(3)

Recommended load capacitance

versus equivalent serial

resistance of the crystal (RS)(4)

RS = 30 Ω

-30-

HSE driving current

VDD = 3.3 V

VIN = VSS with 30 pF

load

Oscillator transconductance

Startup

mA/V

tSU(HSE)

(5)

Startup time

VDD is stabilized

1. Resonator characteristics given by the crystal/ceramic resonator manufacturer.

2. Based on characterization, not tested in production.

3. It is recommended to use high-quality external ceramic capacitors in the 5 pF to 25 pF range (typ.),

designed for high-frequency applications, and selected to match the requirements of the crystal or

resonator. CL1 and CL2, are usually the same size. The crystal manufacturer typically specifies a load

capacitance which is the series combination of CL1 and CL2. PCB and MCU pin capacitance must be

included (10 pF can be used as a rough estimate of the combined pin and board capacitance) when sizing

CL1 and CL2.

4. The relatively low value of the RF resistor offers a good protection against issues resulting from use in a

humid environment, due to the induced leakage and the bias condition change. However, it is

recommended to take this point into account if the MCU is used in tough humidity conditions.

5. tSU(HSE) is the startup time measured from the moment it is enabled (by software) to a stabilized 8 MHz

oscillation is reached. This value is measured for a standard crystal resonator and it can vary significantly

with the crystal manufacturer

Table 22. HSE 4-24 MHz oscillator characteristics(1)(2)

Symbol

Parameter

Conditions

Min

Typ

Max

Unit

STM32F100xD Datasheet(PDF) 52 Page - STMicroelectronics

STM32F100xD Datasheet(HTML) 52 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL