PIC16F7X datasheet(49/174 Pages) MICROCHIP

49 / 174 page

 2002 Microchip Technology Inc.

DS30325B-page 47

PIC16F7X

6.0

TIMER1 MODULE

The Timer1 module is a 16-bit timer/counter consisting

of two 8-bit registers (TMR1H and TMR1L), which are

readable and writable. The TMR1 Register pair

(TMR1H:TMR1L) increments from 0000h to FFFFh

and rolls over to 0000h. The TMR1 Interrupt, if enabled,

is generated on overflow, which is latched in interrupt

flag bit TMR1IF (PIR1<0>). This interrupt can be

enabled/disabled by setting/clearing TMR1 interrupt

enable bit TMR1IE (PIE1<0>).

Timer1 can operate in one of two modes:

• As a timer

• As a counter

The operating mode is determined by the clock select

bit, TMR1CS (T1CON<1>).

In Timer mode, Timer1 increments every instruction

cycle. In Counter mode, it increments on every rising

edge of the external clock input.

Timer1 can be enabled/disabled by setting/clearing

control bit TMR1ON (T1CON<0>).

Timer1 also has an internal “RESET input”. This

RESET can be generated by either of the two CCP

modules as the special event trigger (see Sections 8.1

and 8.2). Register 6-1 shows the Timer1 Control

When the Timer1 oscillator is enabled (T1OSCEN is

set), the RC1/T1OSI/CCP2 and RC0/T1OSO/T1CKI

pins become inputs. That is, the TRISC<1:0> value is

ignored and these pins read as ‘0’.

Additional information on timer modules is available in

the PICmicro™ Mid-Range MCU Family Reference

Manual (DS33023).

T1CON: TIMER1 CONTROL REGISTER (ADDRESS 10h)

U-0

R/W-0

—

T1CKPS1 T1CKPS0 T1OSCEN

T1SYNC

TMR1CS

TMR1ON

bit 7

bit 0

bit 7-6

Unimplemented: Read as ‘0’

bit 5-4

T1CKPS1:T1CKPS0: Timer1 Input Clock Prescale Select bits

= 1:8 Prescale value

= 1:4 Prescale value

= 1:2 Prescale value

= 1:1 Prescale value

bit 3

T1OSCEN: Timer1 Oscillator Enable Control bit

= Oscillator is enabled

= Oscillator is shut-off (the oscillator inverter is turned off to eliminate power drain)

bit 2

T1SYNC: Timer1 External Clock Input Synchronization Control bit

TMR1CS = 1:

= Do not synchronize external clock input

= Synchronize external clock input

TMR1CS = 0:

This bit is ignored. Timer1 uses the internal clock when TMR1CS = 0.

bit 1

TMR1CS: Timer1 Clock Source Select bit

= External clock from pin RC0/T1OSO/T1CKI (on the rising edge)

= Internal clock (FOSC/4)

bit 0

TMR1ON: Timer1 On bit

= Enables Timer1

= Stops Timer1

Legend:

R = Readable bit

W = Writable bit

U = Unimplemented bit, read as ‘0’

- n = Value at POR reset

’1’ = Bit is set

’0’ = Bit is cleared

x = Bit is unknown

PIC16F7X Datasheet(PDF) 49 Page - Microchip Technology

PIC16F7X Datasheet(HTML) 49 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL