| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
A19530LUCX-TN-RDMOOEG-A Datasheet(PDF) 16 Page - Allegro MicroSystems |
|
|
|||||||||||||||||||||||||||||
A19530LUCX-TN-RDMOOEG-A Datasheet(HTML) 16 Page - Allegro MicroSystems |
|
16 / 18 page ![]() High Feature Three-Wire Hall-Effect Transmission Speed and Direction Sensor IC A19530 16 Allegro MicroSystems, LLC 955 Perimeter Road Manchester, NH 03103-3353 U.S.A. www.allegromicro.com POWER DERATING The device must be operated below the maximum junction tem- perature of the device, TJ(max). Under certain combinations of peak conditions, reliable operation may require derating supplied power or improving the heat dissipation properties of the appli- cation. This section presents a procedure for correlating factors affecting operating TJ. (Thermal data is also available on the Allegro MicroSystems website.) The Package Thermal Resistance, RθJA, is a figure of merit sum- marizing the ability of the application and the device to dissipate heat from the junction (die), through all paths to the ambient air. Its primary component is the Effective Thermal Conductivity, K, of the printed circuit board, including adjacent devices and traces. Radiation from the die through the device case, RθJC, is a relatively small component of RθJA. Ambient air temperature, TA, and air motion are significant external factors, damped by overmolding. The effect of varying power levels (Power Dissipation, PD), can be estimated. The following formulas represent the fundamental relationships used to estimate TJ, at PD. PD = VIN × IIN (1) Δ T = PD × RθJA (2) TJ = TA + ΔT (3) For example, given common conditions such as: TA= 25°C, VCC = 12 V, ICC = 8 mA, and RθJA = 270°C/W, then: PD = VCC × ICC = 12 V × 8 mA = 96 mW Δ T = PD × RθJA = 96 mW × 270°C/W = 25.9°C TJ = TA + ΔT = 25°C + 25.9°C = 50.9°C A worst-case estimate, PD(max), represents the maximum allow- able power level (VCC(max), ICC(max)), without exceeding TJ(max), at a selected RθJA and TA. Example: Reliability for VCC at TA=150°C, estimated values based on pac- kage UC, using single layer PCB. Observe the worst-case ratings for the device, specifically: RθJA=270°C/W, TJ(max) =165°C, VCC(max)= 24 V, and ICC = 10 mA. Calculate the maximum allowable power level, PD(max). First, invert equation 3: Δ T(max) = TJ(max) – TA = 165°C – 150°C = 15°C This provides the allowable increase to TJ resulting from internal power dissipation. Then, invert equation 2: PD(max) = ΔT(max) ÷RθJA =15°C÷270°C/W=55.5mW Finally, invert equation 1 with respect to voltage: VCC(est) = PD(max) ÷ ICC= 55.5mW÷10mA=5.55 V The result indicates that, at TA, the application and device can dissipate adequate amounts of heat at voltages ≤VCC(est). Compare VCC(est) to VCC(max). If VCC(est) ≤ VCC(max), then reli- able operation between VCC(est) and VCC(max) requires enhanced RθJA. If VCC(est) ≥ VCC(max), then operation between VCC(est) and VCC(max) is reliable under these conditions. THERMAL CHARACTERISTICS: May require derating at maximum conditions Characteristic Symbol Test Conditions* Value Unit Package Thermal Resistance RθJA 1-layer PCB with copper limited to solder pads 270 °C/W *Additional thermal information available on the Allegro website. |
|
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |