AD9546SLASHPCBZ datasheet(189/205 Pages) AD

189 / 205 page

Data Sheet

AD9546

Rev. 0 | Page 189 of 205

Table 110. Example Conditional Processing Sequence

Instruction

Operation

0x00 to 0x7F

A sequence of register transfer instructions

that execute unconditionally

0xB1

Apply Condition 1

0x00 to 0x7F

A sequence of register transfer instructions

that execute only if the condition ID is 1

0xB2

Apply Condition 2

0xB3

Apply Condition 3

0x00 to 0x7F

A sequence of register transfer instructions that

execute only if the condition ID is 1, 2, or 3

0x91

Calibrate the system clock PLL

0xB0

Clear condition map

0x80

IO update

0xFF

Terminate sequence

Pause Instruction (0xFE)

The EEPROM controller only recognizes the pause instruction

during an upload sequence. Upon encountering a pause

instruction, the EEPROM controller enters an idle state, but

preserves the current value of the EEPROM address pointer.

One use of the pause instruction is for saving multiple, yet

distinct, values of the same AD9546 register, which is useful for

sequencing power-up conditions.

The pause instruction is also useful for executing an upload

sequence requiring more space than is available in the EEPROM

sequence registers (see the EEPROM Upload section).

End of Data Instruction (0xFF)

When the EEPROM controller encounters an end of data

instruction during an upload sequence, it stores the instruction

in EEPROM along with the computed checksum, clears the

EEPROM address pointer, and then enters an idle state. When

encountered during a download sequence, however, the

EEPROM controller clears the EEPROM address pointer,

verifies the checksum, and then enters an idle state.

During EEPROM downloads, condition instructions always

execute unconditionally.

MULTIDEVICE SUPPORT

Multidevice support enables multiple AD9546 devices to share

the contents of a single EEPROM. There are two levels of

multidevice support. Level 1 supports a configuration where

multiple AD9546 devices share a single EEPROM through a

dedicated I2C bus. Level 2 supports a configuration where

multiple AD9546 devices share a single EEPROM connected to

a common I2C bus that includes other I2C master devices.

Figure 125 and Figure 126 show the Level 1 and Level 2

configurations, respectively. Only the I2C functions of the

multifunction pins are shown.

SDA

SCL

CPU

EEPROM

SCL SDA

SCL

SDA

SCL SDA

AD9546

DEVICE 1

SCL SDA

AD9546

DEVICE 2

SCL SDA

Figure 125. Level 1 Multidevice Configuration

AD9546

DEVICE 1

SCL SDA

AD9546

DEVICE 2

SCL SDA

SDA

SCL

CPU

SDA

SCL

EEPROM

SCL

SDA

Figure 126. Level 2 Multidevice Configuration

Multidevice Bus Arbitration

The EEPROM controller implements bus arbitration by

continuously monitoring the SDA and SCL bus signals for start

and stop conditions. The controller can determine whether the

bus is idle or busy. If the bus is busy, the EEPROM controller

delays its pending I2C transfer until a stop condition indicates

that the bus is available.

Bus arbitration is essential in cases where two I2C master

devices simultaneously attempt an I2C transfer. For example, if

one I2C master detects that SDA is Logic 0 when it is intended to

be Logic 1, the master assumes that another I2C master is active

and immediately terminates its own attempt to transfer data.

Similarly, if one I2C master detects that SCL is Logic 0 prior to

entering a start state, the master assumes that another I2C

master is active and stalls its own attempt to drive the bus.

In either case, the prevailing I2C master completes its current

transaction before releasing the bus. Because the postponed I2C

master continuously monitors the bus for a stop condition, it

attempts to seize the bus and carry out the postponed transaction

on detection of such a stop condition.

The EEPROM controller includes an arbitration timer to optimize

the bus arbitration process. Specifically, when the EEPROM

controller postpones an I2C transfer as a result of detecting bus

contention, the arbitration timer starts. If the EEPROM controller

fails to detect a stop condition within 255 SCL cycles, it attempts

to force another transaction. If the bus is still busy, the EEPROM

controller restarts the arbitration timer, and the process continues

until the EEPROM controller eventually completes the pending

transaction.

AD9546/PCBZ Datasheet(PDF) 189 Page - Analog Devices

AD9546/PCBZ Datasheet(HTML) 189 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL