MPC8560 datasheet(57/108 Pages) FREESCALE

57 / 108 page

MPC8560 Integrated Processor Hardware Specifications, Rev. 3.1

Freescale Semiconductor

PCI/PCI-X

Figure 38 provides the AC test load for PCI and PCI-X.

Figure 38. PCI/PCI-X AC Test Load

Figure 39 shows the PCI/PCI-X input AC timing conditions.

Figure 39. PCI-PCI-X Input AC Timing Measurement Conditions

HRESET high to first FRAME assertion

tPCRHFV

—

clocks

8, 11

Notes:

1.Note that the symbols used for timing specifications herein follow the pattern of t(first two letters of functional

block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For

example, tPCIVKH symbolizes PCI/PCI-X timing (PC) with respect to the time the input signals (I) reach the valid

state (V) relative to the SYSCLK clock, tSYS, reference (K) going to the high (H) state or setup time. Also, tPCRHFV

symbolizes PCI/PCI-X timing (PC) with respect to the time hard reset (R) went high (H) relative to the frame signal

(F) going to the valid (V) state.

2.See the timing measurement conditions in the PCI 2.2 Local Bus Specifications.

3.All PCI signals are measured from OVDD/2 of the rising edge of PCI_SYNC_IN to 0.4 × OVDD of the signal in

question for 3.3 V PCI signaling levels.

4.For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current

delivered through the component pin is less than or equal to the leakage current specification.

5.Input timings are measured at the pin.

6.The timing parameter tSYS indicates the minimum and maximum CLK cycle times for the various specified

frequencies. The system clock period must be kept within the minimum and maximum defined ranges. For values

see Section 15, “Clocking.”

7.The setup and hold time is with respect to the rising edge of HRESET.

8.The timing parameter tPCRHFV is a minimum of 10 clocks rather than the minimum of 5 clocks in the PCI 2.2 Local

Bus Specifications.

9.The reset assertion timing requirement for HRESET is 100

µs.

10.Guaranteed by characterization.

11.Guaranteed by design.

Table 42. PCI AC Timing Specifications at 66 MHz (continued)

Parameter

Symbol 1

Min

Max

Unit

Notes

Output

OVDD/2

RL = 50 Ω

Z0 = 50 Ω

tPCIVKH

CLK

Input

tPCIXKH

MPC8560 Datasheet(PDF) 57 Page - Freescale Semiconductor, Inc

MPC8560 Datasheet(HTML) 57 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL