WLD datasheet(39/42 Pages) OMRON

39 / 42 page

Application Variations

Item

Appropriate model/actuator

Details

Changing the installation position

of the actuator

By loosening the Allen-head bolt on

the actuator lever, the position of the

actuator can be set anywhere within

the 360_. With Lamp-equipped

Switches, the actuator lever comes

in contact with the top of the lamp

cover, so use caution when rotating

and setting the lever. When the lever

only moves forwards and backwards,

it will not contact the lamp cover.

Roller Levers: WLCA2, WL01CA2,

WLH2, WL01H2, WLG2, WL01G2

Adjustable Roller Levers: WLCA12,

WL01CA12, WLH12, WL01H12,

WLG12, WL01G12

Adjustable Rod Levers: WLCL,

WL01CL, WLHL, WL01HL, WLGL,

WL01GL

Loosen the M5 × 12 bolt, set the

actuator’s position and then tighten

the bolt again.

Changing the orientation of the

Head

By removing the screws in the four

corners of the Head, the Head can

be set in any of the four directions.

Be sure to change the plunger for

internal operations at the same time.

(The operational plunger does not

need to be changed on overtravel

general-purpose and high-sensitivity

models.) The roller plunger can be

set in either two positions at 90_.

WLCA2-2N and WL01CA2-2N can

only be set in either the forward or

backward direction.

Roller Levers: WLCAj, WL01CAj,

WLGCAj

Adjustable Rod Levers: WLCL,

WL01CL

Horizontal Plungers: WLSDj,

WL01SDj

Roller Plungers: WLD2, WL01D2

Sealed Roller Plungers: WLD28,

WL01D28.

Note: Does not include -RP60

Series or -141 Series.

Loosen the screws.

Head

Loosen

the

screws.

Head

Changing the operating direction

By removing the Head on models

which can operate on one-side only,

and then changing the direction of

the operational plunger, one of three

operating directions can be selected.

In the case of overtravel models, as

noted on page 20, by loosening the

rubber holder using either a coin or a

flat-blade screwdriver, and changing

the direction of the internal rubber

section, one of three operating

directions can be selected.

The tightening torque for the screws

on the Head is 0.78 to 0.88 N S m. (8

to9kg S cm)

Roller Levers: WLCAj, WL01CAj

Adjustable Roller Levers: WLCA12,

WL01CA12

Adjustable Rod Levers: WLCL,

WL01CL

Overtravel Models: WLCAj-2N,

WL01CAj-2N

Note:

The diagram at the right is not

correct for the overtravel -2N

models.

The output of the

Switch will be changed,

regardless of which

direction the lever is

pushed.

Operating

Not operating

Clockwise operation

Counterclockwise

operation

Not operating

Operating

The output of the

Switch will only be

changed when the lever

is pushed in one

direction.

Operation in

both directions

For details on overtravel -2N models, refer to page 19.

Operational

plunger

Installing the roller on the inside

By installing the roller lever in the

opposite direction, the roller can be

installed on the inside. (Set so that

operation can be completed within a

180_ level range.)

Roller Levers: WLCAj, WL01CAj,

except for the adjustable roller

levers.

Fork Lever Locks: WLCA32-4j,

WL01CA32-4j

Loosen the

Allen-head bolt.

WLD Datasheet(PDF) 39 Page - Omron Electronics LLC

WLD Datasheet(HTML) 39 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

Datasheet Descarga

Enlace URL