| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
ST60A3H1 Datasheet(PDF) 6 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
ST60A3H1 Datasheet(HTML) 6 Page - STMicroelectronics |
|
6 / 72 page ![]() 2.2 eUSB2 tunneling eUSB2 tunneling configurations use the TX_IP, TX_IN differential pins for data transmission over the RF channel, and the RX_OP, RX_ON differential pins for data reception on the RF channel. Figure 4 illustrates the data path in eUSB2 tunneling configurations. The four GPIOs that are not used for eUSB2 tunneling can be used as alternate GPIOs. Figure 4. Data path in eUSB2 tunneling configurations RF IN RF OUT Half Duplex Digital PMU ULP, LP clock CMOS IO Demodulator Receiver VCO Transmitter Power UART/GPIO/ I²C Power Data Control UART/GPIO/ I²C Low-speed digital Protocol / State Config / Status Calibration RX_OP RX_ON Line driver eUSB2 OUTPUT(1) eUSB2 TX_IP TX_IN eUSB2 INPUT(1) eUSB2 VDD_IO 1.8 V 1.8 V Line receiver VDD_1V8 Decoupling capacitors CFG_SDA RF_EN LINK_STATUS MODE_INT CFG_SCL CFG_I2C Control RF RF IN path RF OUT path 1. TX_IP and RX_OP, as well as TX_IN and RX_ON respectively, must be tied together on the board. Dual-linear-polarization antenna Alternate GPIOs (if not used for tunneling) / SDA / GPIO[3] / SCL / GPIO[2] TXD / SCL / GPIO[0] RXD / SDA / GPIO[1] UART / I²C / GPIO Low data rate tunneling / I²C / - - - - The electrical characteristics of these lines are configurable: • DC coupled differential I/Os eUSB2 • Single ended I/Os for eUSB2 Low Speed and Full Speed. All three eUSB2 speed rates are supported: • Low Speed (LS) at 1.5 Mbit/s • Full Speed (FS) at 12 Mbit/s • High Speed (HS) at 480 Mbit/s An ST60A3H1 pair, configured to tunnel eUSB2 traffic behaves as an eUSB2 Hybrid Repeater, as defined in appendix B of the eUSB2 specification [1]. A Hybrid Repeater refers to a device hosting an upstream eUSB2 interface and a downstream eUSB2 interface. Based on the eUSB2 specification [1], a few aspects of the Hybrid Repeater setup that are worth noting are mentioned here: The ST60A3H1 is configured to support the Hybrid Repeater configuration 4, shown below with ST60A3H1 eUSB2 mode (Port only) and eUSB2 port type (eUSPr or eDSPr). The ST60A3H1 can have two different roles: • Local Host configured with an I²C configuration bus • Remote Host configured over the air from the Local ST60A3H1. This leads to the two possible configurations 4 (4_LH and 4_RH) presented in Figure 5. ST60A3H1 Functional description DS14598 - Rev 2 page 6/72 |
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |