Motor de Búsqueda de Datasheet de Componentes Electrónicos
  Mexican  ▼
ALLDATASHEET.COM.MX

X  

ST60A3H1 Datasheet(PDF) 21 Page - STMicroelectronics

No. de pieza ST60A3H1
Descripción Electrónicos  60 GHz V-band contactless connectivity transceiver with linear-polarization integrated antenna, and tunneling eUSB2, UART, GPIO or I²C
PDF  72 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Fabricante Electrónico  STMICROELECTRONICS [STMicroelectronics]
Página de inicio  http://www.st.com
Logo STMICROELECTRONICS - STMicroelectronics

ST60A3H1 Datasheet(HTML) 21 Page - STMicroelectronics

Back Button ST60A3H1 Datasheet HTML 17Page - STMicroelectronics ST60A3H1 Datasheet HTML 18Page - STMicroelectronics ST60A3H1 Datasheet HTML 19Page - STMicroelectronics ST60A3H1 Datasheet HTML 20Page - STMicroelectronics ST60A3H1 Datasheet HTML 21Page - STMicroelectronics ST60A3H1 Datasheet HTML 22Page - STMicroelectronics ST60A3H1 Datasheet HTML 23Page - STMicroelectronics ST60A3H1 Datasheet HTML 24Page - STMicroelectronics ST60A3H1 Datasheet HTML 25Page - STMicroelectronics Next Button
Zoom Inzoom in Zoom Outzoom out
 21 / 72 page
background image
2.8.1
RESET state
See Section 2.7: Resets for a complete description.
2.8.2
RF_IDLE state
RF_IDLE state serves the following purpose:
•
The ST60A3H1 registers are fully accessible for their respective supported mode (read only, read/write or
write only).
•
It can be skipped by ensuring that the RF_EN pin is tied to VDD_IO (always active device). This is however
an option only available for a Remote device. For a Local device, RF_EN must be controlled for
configuration purposes.
•
All states eventually return to RF_IDLE state when RF_EN = 0.
•
Power consumption is very limited as all analog and RF blocks are disabled. Optimal power consumption is
obtained by disabling the pull-up resistor on the RF_EN pin through register programming.
The transition from RF_IDLE to RF_DETECT state is ensured by setting RF_EN = 1. Refer to Section 2.7.3: Entry
into RF_IDLE state for details on the RF_EN pin.
2.8.3
RF_DETECT state
RF_DETECT phases are the following:
•
RF LINK RESET
–
All internal state machines are reset. Configuration registers, and possible error reports are kept
unchanged.
–
If RF_DETECT is re-entered after an error such as loss of RF link, insufficient RF link quality or an
error during a previous pairing attempt, the RF detection procedure is repeated indefinitely.
•
SEEK
–
This is the actual power optimized search for an RF partner (see Section 2.8.3.1: SEEK phase)
–
The SEEK state loops until an RF partner has been found.
•
LINK TRAINING
–
Once an RF partner has been found, LINK TRAINING is entered for optimal RF link budget.
–
The two RF partners exchange internal configuration parameters such as Remote or Local role.
–
This phase can lead to an aborted connection.
LINK_STATUS is raised on exiting RF_DETECT and entering LOW_POWER state. EVT_LINK_ENABLED
replicates LINK_STATUS (see Section 3: Interrupts and errors).
2.8.3.1
SEEK phase
This section describes the procedure implemented by the ST60A3H1 when searching for an RF partner.
The schemes implemented by the ST60A3H1 for the initial discovery aim at achieving the best power
consumption / connection time compromise. Whenever possible most parts of the device are switched off outside
specific periods. The parameters driving the initial discovery are configurable with default values such that the
average consumption during the detection phase is around a few tens of µA and the average detection time is in
the order of 0.5 seconds.
There are two ways of performing initial discovery in RF_DETECT state:
•
Full detection
•
Passive detection
Pairing is only possible with one device in Full Detection and the other in Passive Detection. The Passive
detection is selected by default for a Remote device at power-up reset. For a Local device with Full detection, the
ST60A3H1 must be reconfigured (see Section 2.7.1.3: Power-up reset).
The initial discovery is based on periodic time frames, with the aim of switching off all possible parts of the
devices outside active seeking periods.
ST60A3H1
Functional description
DS14598 - Rev 2
page 21/72



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72


Datasheet Descarga

Go To PDF Page


Enlace URL



¿ALLDATASHEET es útil para Ud.?  [ DONATE ] 

Todo acerca de Alldatasheet   |   Publicidad   |   Contáctenos   |   Política de Privacidad   |   Enlace a la hoja de datos    |   Intercambio de Enlaces   |   Lista de Fabricantes
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com