TDA9112 datasheet(24/51 Pages) STMICROELECTRONICS

24 / 51 page

TDA9112

24/51

Note 50: With exception of

HDUTY and BREF adjustments data that can take effect instantaneously if switches

HDutySyncV and B+SyncV are at 0 respectively.

Note 51: In Read Mode, the device always outputs data of the status register, regardless of sub address previously

selected.

Note 52: The TV, TH, TVM and THM bits are for testing purposes and must be kept at 0 by application.

Description of I2C Bus switches and flags

Write-to bits

Sad00/D7 - HDutySyncV

Synchronization of internal application of Hori-

zontal Duty cycle data, buffered in I2C Bus latch,

with internal discharge of Vertical oscillator

0: Asynchronous mode, new data applied

with ACK bit of I2C Bus transfer on this sub

address

1: Synchronous mode

Sad02/D7 - HMoiré

Horizontal Moiré characteristics

0: Adapted to an architecture with EHT gener-

ated in deflection section

1: Adapted to an architecture with separated

deflection and EHT sections

Sad03/D7 - B+SyncV

Same as HDutySyncV, applicable for B+ refer-

ence data

Sad04/D7 - HDyCorTr

Tracking of Horizontal Dynamic Correction

waveform amplitude with Horizontal Size at ad-

justment and EHT variation (voltage of HEHTIn).

0: Not active

1: Active

Sad05/D7 - HDyCorPh

Phase of start of Horizontal Dynamic Correction

waveform (and B+ drive if in internal sawtooth

configuration) in relation to horizontal flyback

pulse.

0: Start of the flyback

1: Middle of the flyback

Reserved

PCAC

(Pin cushion asymmetry correction)

100

000

Reserved

PARAL

(Parallelogram correction)

100

000

Reserved

TCAC

(Top corner asymmetry correction)

100

000

Reserved

BCAC

(Bottom corner asymmetry correction)

100

000

VDyCorPol

0:”

∪”

VDC-AMP

(Vertical dynamic correction amplitude)

100

000

XRayReset

0: No effect

1: Reset

VSyncAuto

1:On

VSyncSel

0:Comp

1:Sep

SDetReset

0: No effect

1: Reset

PLL1Pump

1: Fast

0: Slow

PLL1InhEn

1:On

HLockEn

1:On

0:Off(52)

TVM

0:Off(52)

THM

0: Off(52)

BOHEdge

0: Falling

HBOutEn

0: Disable

VOutEn

0: Disable

BlankMode

1: Perm.

READ MODE (SLAVE ADDRESS = 8D)

(51)

HLock

0: Locked

1: Not locked

VLock

0: Locked

1: Not lock.

XRayAlarm

1: On

0: Off

Polarity detection

Sync detection

HVPol

1: Negative

VPol

1: Negative

VExtrDet

0: Not det.

HVDet

0: Not det.

VDet

0: Not det.

Sad

D6D5

D3D2

D1D0

TDA9112 Datasheet(PDF) 24 Page - STMicroelectronics

TDA9112 Datasheet(HTML) 24 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51

Datasheet Descarga

Enlace URL