MPC8640DEC datasheet(45/140 Pages) FREESCALE

45 / 140 page

MPC8640 and MPC8640D Integrated Host Processor Hardware Specifications, Rev. 1

Freescale Semiconductor

Local Bus

Figure 25 provides the AC test load for the local bus.

Local bus clock to output valid (except

LAD/LDP and LALE)

tLBKHOV1

—2.0

Local bus clock to data valid for

LAD/LDP

tLBKHOV2

—2.2

Local bus clock to address valid for

LAD

tLBKHOV3

—2.3

Local bus clock to LALE assertion

tLBKHOV4

—2.3

Output hold from local bus clock

(except LAD/LDP and LALE)

tLBKHOX1

0.7

—

Output hold from local bus clock for

LAD/LDP

tLBKHOX2

0.7

—

Local bus clock to output high

Impedance (except LAD/LDP and

LALE)

tLBKHOZ1

—2.5

Local bus clock to output high

impedance for LAD/LDP

tLBKHOZ2

—2.5

Note:

1. The symbols used for timing specifications herein follow the pattern of t(First two letters of functional

block)(signal)(state) (reference)(state) for inputs and t(First two letters of functional

block)(reference)(state)(signal)(state) for outputs. For example, tLBIXKH1 symbolizes local bus timing

(LB) for the input (I) to go invalid (X) with respect to the time the tLBK clock reference (K) goes

high (H), in this case for clock one(1). Also, tLBKHOX symbolizes local bus timing (LB) for the

tLBK clock reference (K) to go high (H), with respect to the output (O) going invalid (X) or output

hold time.

2. All timings are in reference to LSYNC_IN for PLL enabled and internal local bus clock for PLL

bypass mode.

3. All signals are measured from OVDD/2 of the rising edge of LSYNC_IN for PLL enabled or

internal local bus clock for PLL bypass mode to 0.4

× OVDD of the signal in question for 3.3-V

signaling levels.

4. Input timings are measured at the pin.

5. For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when

the total current delivered through the component pin is less than or equal to the leakage

current specification.

6. tLBOTOT is a measurement of the minimum time between the negation of LALE and any

change in LAD. tLBOTOT is programmed with the LBCR[AHD] parameter.

7. Maximum possible clock skew between a clock LCLK[m] and a relative clock LCLK[n]. Skew

measured between complementary signals at BVDD/2.

8. Guaranteed by design.

Table 40. Local Bus Timing Parameters (OVDD = 3.3 V)m - PLL Enabled (continued)

Parameter

Symbol 1

Min

Max

Unit

Notes

MPC8640DEC Datasheet(PDF) 45 Page - Freescale Semiconductor, Inc

MPC8640DEC Datasheet(HTML) 45 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL