MPC5634M datasheet(59/118 Pages) FREESCALE

59 / 118 page

Electrical characteristics

MPC5634M Microcontroller Data Sheet, Rev. 4

Preliminary—Subject to Change Without Notice

Freescale Semiconductor

Maximum operating

temperature range15 – die

junction temperature

– 40.0

150.0

TSTG

Storage temperature

range

– 55.0

150.0

TSDR

Maximum solder

temperature16

—

260.0

MSL

Moisture sensitivity level17

—3

—

1 Functional operating conditions are given in the DC electrical specifications. Absolute maximum ratings are stress

ratings only, and functional operation at the maxima is not guaranteed. Stress beyond the listed maxima may affect

device reliability or cause permanent damage to the device.

2 TBD: To Be Defined.

3 Allowed 2 V for 10 hours cumulative time, remaining time at 1.2 V +10%.

4 The V

FLASH supply is connected to VRC33 in the package substrate. This specification applies to calibration package

devices only.

5 Allowed 5.3 V for 10 hours cumulative time, remaining time at 3.3 V +10%.

6 Allowed 6.8 V for 10 hours cumulative time, remaining time at 5 V +10%.

7 The pin named as V

RC33 is internally connected to the pads VFLASH and VRC33 in the 144 LQFP package. These

limits apply when the internal regulator is disabled and VRC33 power is supplied externally.

8 All functional non-supply I/O pins are clamped to V

SS and VDDE, or VDDEH.

9 AC signal overshoot and undershoot of up to 2.0 V of the input voltages is permitted for an accumulative duration of

60 hours over the complete lifetime of the device (injection current not limited for this duration).

10 Internal structures hold the voltage greater than –1.0 V if the injection current limit of 2 mA is met.

11 Internal structures hold the input voltage less than the maximum voltage on all pads powered by V

DDEH supplies, if

the maximum injection current specification is met (2 mA for all pins) and VDDEH is within the operating voltage

specifications.

12 Internal structures hold the input voltage less than the maximum voltage on all pads powered by V

DDE supplies, if the

maximum injection current specification is met (2 mA for all pins) and VDDE is within the operating voltage

specifications.

13 Total injection current for all pins (including both digital and analog) must not exceed 25 mA.

14 Total injection current for all analog input pins must not exceed 15 mA.

15 Lifetime operation at these specification limits is not guaranteed.

16 Solder profile per CDF-AEC-Q100.

17 Moisture sensitivity per JEDEC test method A112.

Table 8. Absolute maximum ratings1 (continued)

Symbol

Parameter

Conditions

Value2

Unit

min

max

MPC5634M Datasheet(PDF) 59 Page - Freescale Semiconductor, Inc

MPC5634M Datasheet(HTML) 59 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL