| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
AS3607 Datasheet(PDF) 51 Page - ams AG |
|
|
|||||||||||||||||||||||||||||
AS3607 Datasheet(HTML) 51 Page - ams AG |
|
51 / 71 page ![]() www.austriamicrosystems.com Revision 1.03 50 - 70 AS3606 AS3607 2v2 Data Sheet - R e g i s t e r D e f i n i t i o n Table 38. Out_Cntr Register Name Base Default Out_Cntr 2-wire serial 00h Offset: 1Ah-1 DCDC mode and XIRQ Output Control Register This is an extended register and needs to be enabled by writing 001b to Reg. 1Ch first. This register is reset at a VDD27-POR or XRES input. Bit Bit Name Default Access Bit Description 7 DCDC23_1.4A 0 R/W Combines DCDC2 and DCDC3 to one regulator for 1.4A output currents 0: DCDC2 and DCDC3 working independent 1: DCDC2 & DCDC3 combined for 1.4A (DCDC3 registers have no effect) 6 GPIO_HBN_ON 0 R/W 0: Hibernation enable via GPIOs disabled 1: Hibernation enalbe via GPIOs enabled GPIO selected via GPIO_DIMM_HBN_SEL <1:0> 5:4 HBN_DELAY<1:0> 00 R/W Sets the delay time for going into hibernation after writing to register 17-4h 00: 0ms 01: 8ms 10: 16ms 11: 32ms 3:2 DRIVE_XIRQ<1:0> 00 R/W Sets the XIRQ output pin to open-drain, push-pull or tri-state and sets various driving strengths 00: 6mA open-drain output 01: 6mA push-pull output 10: 1mA push-pull output 11: HiZ, tri-state 1:0 MUX_XIRQ<1:0> 00 R/W Multiplexes various digital signals to the XIRQ output pin 00: XIRQ, active low interrupt request signal 01: CLKINT1, internal clock signal, see Clk_Cntr register 10: CLKINT2, internal clock signal, see Clk_Cntr register 11: IRQ, active low reset signal Table 39. Clk_Cntr Register Name Base Default Clk_Cntr 2-wire serial 00h Offset: 1Ah-2 Clock Control Register This is an extended register and needs to be enabled by writing 010b to Reg. 1Ch first. This register is reset at a VDD27-POR or XRES input. Bit Bit Name Default Access Bit Description 7:6 CLKINT2<1:0> 00 R/W Selects the CLKINT2 input source. Note, this is an internal clock, which can be multiplexed to the XRES output. 00: LOW, drives the signal to logic “0” 01: CLK1Hz charger 10: do not use 11: HIGH, drives the signal to logic “1” 5:4 CLKINT1<1:0> 00 R/W Selects the CLKINT1 frequency. Note, this is an internal clock, which can be multiplexed to XIRQ output. 00: 2MHz 01: 1MHz 10: 1kHz 11: 125Hz |
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |