TNETV1644ZDU6 datasheet(49/306 Pages) TI1

49 / 306 page

TMS320DM6437

Digital Media Processor

www.ti.com

SPRS345D – NOVEMBER 2006 – REVISED JUNE 2008

Table 2-18. Host-Port Interface Terminal Functions

SIGNAL

TYPE(1)

OTHER(2)(3)

DESCRIPTION

ZWT

ZDU

NAME

NO.

Host-Port Interface (HPI)

HD0/VLYNQ_SCRUN/

IPU

AD18/GP[58]

DVDD33

HD1/VLYNQ_RXD0/

AD16/GP[59]

HD2/VLYNQ_RXD1/

AD17/GP[60]

HD3/VLYNQ_RXD2/

PCBE2/GP[61]

HD4/VLYNQ_RXD3/

PFRAME/GP[62]

HD5/VLYNQ_TXD0/

PIRDY/GP[63]

HD6/VLYNQ_TXD1/

PTRDY/GP[64]

This pin is multiplexed between HPI, VLYNQ or EMAC, PCI,

HD7/VLYNQ_TXD2/

and GPIO.

PDEVSEL/GP[65]

I/O/Z

In HPI mode, these pins are host-port data pins HD[15:0]

HD8/VLYNQ_TXD3/

IPD

(I/O/Z) and are multiplexed internally with the HPI address

PPERR/GP[66]

DVDD33

lines.

HD9/MCOL/

PSTOP/GP[67]

HD10/MCRS/

PSERR/GP[68]

HD11/MTXD3/

PCBE1/GP[69]

HD12/MTXD2/

PPAR/GP[70]

HD13/MTXD1/

AD14/GP[71]

HD14/MTXD0/

AD15/GP[72]

HD15/MTXCLK/

AD12/GP[73]

This pin is multiplexed between HPI, EMAC, PCI, and GPIO.

HHWIL/MRXDV/

IPD

I/O/Z

In HPI mode, this pin is half-word identification input HHWIL

AD13/GP[74]

DVDD33

(I).

This pin is multiplexed between HPI, EMAC, PCI, and GPIO.

In HPI mode, this pin is control input 1 HCNTL1 (I). The state

HCNTL1/MTXEN/

IPD

I/O/Z

of HCNTL1 and HCNTL0 determines if address, data, or

AD11/GP[75]

DVDD33

control information is being transmitted between an external

host and the DM6437.

This pin is multiplexed between HPI, EMAC, PCI, and GPIO.

In HPI mode, this pin is control input 0 HCNTL0 (I). The state

HCNTL0/MRXER/

IPD

I/O/Z

of HCNTL1 and HCNTL0 determines if address, data, or

AD10/GP[76]

DVDD33

control information is being transmitted between an external

host and the DM6437.

This pin is multiplexed between HPI, EMAC, PCI, and GPIO.

HR/W/MRXCLK/

IPD

I/O/Z

In HPI mode, this pin is host read or write select input

AD8/GP[77]

DVDD33

HR/W(I).

HDS2/MRXD0/

IPU

This pin is multiplexed between HPI, EMAC, PCI, and GPIO.

I/O/Z

AD9/GP[78]

DVDD33

In HPI mode, this pin is host data strobe input 2 HDS2 (I).

(1)

I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal

(2)

IPD = Internal pulldown, IPU = Internal pullup. For more detailed information on pullup/pulldown resistors and situations where external

pullup/pulldown resistors are required, see Section 3.9.1, Pullup/Pulldown Resistors.

(3)

Specifies the operating I/O supply voltage for each signal

Submit Documentation Feedback

Device Overview

TNETV1644ZDU6 Datasheet(PDF) 49 Page - Texas Instruments

TNETV1644ZDU6 Datasheet(HTML) 49 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL