Motor de Búsqueda de Datasheet de Componentes Electrónicos
  Mexican  ▼
ALLDATASHEET.COM.MX

X  

M48T212AMH Datasheet(PDF) 14 Page - STMicroelectronics

No. de pieza M48T212AMH
Descripción Electrónicos  3.3V TIMEKEEPER CONTROLLER
PDF  20 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Fabricante Electrónico  STMICROELECTRONICS [STMicroelectronics]
Página de inicio  http://www.st.com
Logo STMICROELECTRONICS - STMicroelectronics

M48T212AMH Datasheet(HTML) 14 Page - STMicroelectronics

Back Button M48T212AMH Datasheet HTML 10Page - STMicroelectronics M48T212AMH Datasheet HTML 11Page - STMicroelectronics M48T212AMH Datasheet HTML 12Page - STMicroelectronics M48T212AMH Datasheet HTML 13Page - STMicroelectronics M48T212AMH Datasheet HTML 14Page - STMicroelectronics M48T212AMH Datasheet HTML 15Page - STMicroelectronics M48T212AMH Datasheet HTML 16Page - STMicroelectronics M48T212AMH Datasheet HTML 17Page - STMicroelectronics M48T212AMH Datasheet HTML 18Page - STMicroelectronics Next Button
Zoom Inzoom in Zoom Outzoom out
 14 / 20 page
background image
M48T212A
14/20
VCC SWITCH OUTPUT
Vccsw output goes low when VOUT switches to
VCC turning on a customer supplied P-Channel
MOSFET
(see
Figure
3).
The
Motorola
MTD20P06HDL is recommended. This MOSFET
in turn connects VOUT to a separate supply when
the current requirement is greater than IOUT1 (see
Table 7). This output may also be used simply to
indicate the status of the internal battery switcho-
ver comparator, which controls the source (VCC or
battery) of the VOUT output.
POWER-ON RESET
The M48T212A continuously monitors VCC. When
VCC falls to the power fail detect trip point, the RST
pulls low (open drain) and remains low on power-
up for 40 to 200ms after VCC passes VPFD. The
RST pin is an open drain output and an appropri-
ate pull-up resistor to VCC should be chosen to
control rise time.
Note: If the RST output is fed back into either of
the RSTIN inputs (for a microprocessor with a bi-
directional reset) then a 1k
Ω (max) pull-up resistor
is recommended.
Reset Inputs (RSTIN1 & RSTIN2)
The M48T212A provides two independent inputs
which can generate an output reset. The duration
and function of these resets is identical to a reset
generated by a power cycle. Table 14 and Figure
12 illustrate the AC reset characteristics of this
function. During the time RST is enabled (tR1HRH
& tR2HRH), the Reset Inputs are ignored.
Note: RSTIN1 and RSTIN2 are each internally
pulled up to VCC through a 100KΩ resistor.
Calibrating the Clock
The M48T212A is driven by a quartz controlled os-
cillator with a nominal frequency of 32,768 Hz. The
devices are tested not to exceed ±35 ppm (parts
per million) oscillator frequency error at 25°C,
which equates to about ±1.53 minutes per month.
When the Calibration circuit is properly employed,
accuracy improves to better than +1/–2 ppm at
25°C.
The oscillation rate of crystals changes with tem-
perature. The M48T212A design employs periodic
counter correction. The calibration circuit adds or
subtracts counts from the oscillator divider circuit
at the divide by 256 stage, as shown in Figure 11.
The number of times pulses which are blanked
(subtracted, negative calibration) or split (added,
positive calibration) depends upon the value load-
ed into the five Calibration bits found in the Control
Register. Adding counts speeds the clock up, sub-
tracting counts slows the clock down.
The Calibration bits occupy the five lower order
bits (D4-D0) in the Control Register 8h. These bits
can be set to represent any value between 0 and
31 in binary form. Bit D5 is a Sign bit; ’1’ indicates
positive calibration, ’0’ indicates negative calibra-
tion. Calibration occurs within a 64 minute cycle.
The first 62 minutes in the cycle may, once per
minute, have one second either shortened by 128
or lengthened by 256 oscillator cycles.
If a binary ’1' is loaded into the register, only the
first 2 minutes in the 64 minute cycle will be modi-
fied; if a binary 6 is loaded, the first 12 will be af-
fected, and so on.
Therefore, each calibration step has the effect of
adding 512 or subtracting 256 oscillator cycles for
every 125,829,120 actual oscillator cycles, that is
+4.068 or –2.034 ppm of adjustment per calibra-
tion step in the calibration register. Assuming that
the oscillator is running at exactly 32,768 Hz, each
of the 31 increments in the Calibration byte would
represent +10.7 or –5.35 seconds per month
which corresponds to a total range of +5.5 or –2.75
minutes per month.
Two methods are available for ascertaining how
much calibration a given M48T212A may require.
The first involves setting the clock, letting it run for
a month and comparing it to a known accurate ref-
erence and recording deviation over a fixed period
of time. Calibration values, including the number of
seconds lost or gained in a given period, can be
found in Application Note AN934: TIMEKEEPER
Calibration.
This allows the designer to give the end user the
ability to calibrate the clock as the environment re-
quires, even if the final product is packaged in a
non-user serviceable enclosure. The designer
could provide a simple utility that accesses the
Calibration byte.
The second approach is better suited to a manu-
facturing environment, and involves the use of the
IRQ/FT pin. The pin will toggle at 512Hz, when the
Stop bit (ST, D7 of 9h) is ’0’, the Frequency Test
bit (FT, D6 of Ch) is ’1’, the Alarm Flag Enable bit
(AFE, D7 of 6h) is ’0’, and the Watchdog Steering
bit (WDS, D7 of 7h) is ’1’ or the Watchdog Register
(7h = 0) is reset.
Any deviation from 512 Hz indicates the degree
and direction of oscillator frequency shift at the test
temperature.
For
example,
a
reading
of
512.010124 Hz would indicate a +20 ppm oscilla-
tor frequency error, requiring a –10 (WR001010)
to be loaded into the Calibration Byte for correc-
tion. Note that setting or changing the Calibration
Byte does not affect the Frequency test output fre-
quency.
The IRQ/FT pin is an open drain output which re-
quires a pull-up resistor to VCC for proper opera-
tion. A 500-10k
Ω resistor is recommended in order
to control the rise time. The FT bit is cleared on
power-up.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20


Datasheet Descarga

Go To PDF Page


Enlace URL



¿ALLDATASHEET es útil para Ud.?  [ DONATE ] 

Todo acerca de Alldatasheet   |   Publicidad   |   Contáctenos   |   Política de Privacidad   |   Enlace a la hoja de datos    |   Intercambio de Enlaces   |   Lista de Fabricantes
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com