| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
M48T212AMH Datasheet(PDF) 15 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
M48T212AMH Datasheet(HTML) 15 Page - STMicroelectronics |
|
15 / 20 page ![]() 15/20 M48T212A BATTERY LOW WARNING The M48T212A automatically performs battery voltage monitoring upon power-up and at factory- programmed time intervals of approximately 24 hours. The Battery Low (BL) bit, Bit D4 of Flags Register 0h, will be asserted if the battery voltage is found to be less than approximately 2.5V. The BL bit will remain asserted until completion of bat- tery replacement and subsequent battery low monitoring tests, either during the next power-up sequence or the next scheduled 24-hour interval. If a battery low is generated during a power-up se- quence, this indicates that the battery is below ap- proximately 2.5 volts and may not be able to maintain data integrity in the SRAM. Data should be considered suspect and verified as correct. A fresh battery should be installed. If a battery low indication is generated during the 24-hour interval check, this indicates that the bat- tery is near end of life. However, data is not com- promised due to the fact that a nominal Vcc is supplied. In order to insure data integrity during subsequent periods of battery back-up mode, the battery should be replaced. The battery should be replaced with VCC powering the device to avoid data loss. The M48T212A only monitors the battery when a nominal Vcc is applied to the device. Thus applica- tions which require extensive durations in the bat- tery back-up mode should be powered-up periodically (at least once every few months) in or- der for this technique to be beneficial. Additionally, if a battery low is indicated, data in- tegrity should be verified upon power-up via a checksum or other technique. Note: Battery Low warning is only valid when us- ing a 3V button cell battery. Use a super capacitor for back-up supply causes the BL flag to be invalid. INITIAL POWER-ON DEFAULTS Upon application of power to the device, the fol- lowing register bits are set to a ’0' state: WDS, BMB0-BMB4, RB0-RB1, AFE, ABE, W and FT (See Table 16). Table 14. Reset AC Characteristics (TA = 0 to 70°C; VCC = 3V to 3.6V) Note: 1. Pulse width less than 50ns will result in no RESET (for noise immunity). 2. Pulse width less than 20ms will result in no RESET (for noise immunity). 3. CL = 5pF (see Figure 4). Table 15. Crystal Electrical Characteristics (Externally Supplied) Note: Load capacitors are integrated within the M48T212A. Circuit board layout considerations for the 32kHz crystal of minimum trace lengths and isolation from RF generating signals should be taken into account. ST recommends the KDS DT-38 Tuning Fork Type quartz crystal for all temperature operations. KDS can be contacted at 913-491-6825 or at http://www.kdsj.co.jp for forther information on this crystal type. Symbol Parameter Min Max Unit tR1 (1) RSTIN1 Low to RSTIN1 High 200 ns tR2 (2) RSTIN2 Low to RSTIN2 High 100 ms tR1HRH (3) RSTIN1 High to RST High 40 200 ms tR2HRH (3) RSTIN2 High to RST High 40 200 ms Symbol Description Min Typ Max Unit fO Resonant Frequency 32,768 kHz RS Series Resistance 50 70 k Ω CL Load Capacitance 12.5 pF |
|
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |