DAC5687IPZP datasheet(52/79 Pages) TI

52 / 79 page

www.ti.com

Analog Current Outputs

DAC5687

SLWS164E – FEBRUARY 2005 – REVISED SEPTEMBER 2006

The full-scale output current is set using external resistor RBIAS in combination with an on-chip band-gap voltage

reference source (1.2 V) and control amplifier. Current IBIAS through resistor RBIAS is mirrored internally to provide

a full-scale output current equal to 16 times IBIAS. The full-scale current IOUTFS can be adjusted from 20 mA

down to 2 mA.

The relation between IOUT1 and IOUT2 can be expressed as:

IOUT1 = –IOUTFS – IOUT2

Current flowing into a node is denoted as – current, and current flowing out of a node as + current. Because the

output stage is a current sink, the current can only flow from AVDD into the IOUT1 and IOUT2 pins. If IOUT2 =

–5 mA and IOUTFS = 20 mA then:

IOUT1 = –20 – (–5) = –15 mA

The output current flow in each pin driving a resistive load can be expressed as:

IOUT1 = IOUTFS × CODE / 65,536

IOUT2 = IOUTFS × (65,535 – CODE) / 65,536

where CODE is the decimal representation of the DAC data input word.

For the case where IOUT1 and IOUT2 drive resistor loads RL directly, this translates into single-ended voltages

at IOUT1 and IOUT2:

VOUT1 = AVDD – | IOUT1 |

× R

VOUT2 = AVDD – | IOUT2 |

× R

Assuming that the data is full scale (65,535 in offset binary notation) and RL is 25 Ω, the differential voltage

between pins IOUT1 and IOUT2 can be expressed as:

VOUT1 = AVDD – | –20 mA |

× 25 Ω = 2.8 V

VOUT2 = AVDD – | –0 mA |

× 25 Ω = 3.3 V

VDIFF = VOUT1 – VOUT2 – 0.5 V

Note that care should be taken not to exceed the compliance voltages at node IOUT1 and IOUT2, which would

lead to increased signal distortion.

Figure 59 shows a simplified schematic of the current source array output with corresponding switches.

Differential switches direct the current of each individual NMOS current source to either the positive output node

IOUT1 or its complementary negative output node IOUT2. The output impedance is determined by the stack of

the current sources and differential switches, and is typically >300 k

Ω in parallel with an output capacitance of

5 pF.

The external output resistors are referred to AVDD. The minimum output compliance at nodes IOUT1 and IOUT2

is limited to AVDD – 0.5 V. The maximum output compliance voltage at nodes IOUT1 and IOUT2 equals AVDD +

0.5 V. Beyond this value, transistor breakdown may occur, resulting in reduced reliability of the DAC5687 device.

Exceeding the minimum output compliance voltage adversely affects distortion performance and integral

nonlinearity. The optimum distortion performance for a single-ended or differential output is achieved when the

maximum full-scale signal at IOUT1 and IOUT2 is in the range of AVDD ±0.5 V.

Submit Documentation Feedback

Product Folder Link(s): DAC5687

DAC5687IPZP Datasheet(PDF) 52 Page - Texas Instruments

DAC5687IPZP Datasheet(HTML) 52 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79

Datasheet Descarga

Enlace URL