S25FL128SDPNFAQ datasheet(59/149 Pages) CYPRESS

59 / 149 page

Document Number: 001-98283 Rev. *M

Page 58 of 148

S25FL128S/S25FL256S

Data Protection

8.1

Secure Silicon Region (OTP)

The device has a 1024-byte One Time Program (OTP) address space that is separate from the main flash array. The OTP area is

divided into 32, individually lockable, 32-byte aligned and length regions.

The OTP memory space is intended for increased system security. OTP values can “mate” a flash component with the system CPU/

ASIC to prevent device substitution. See Section 7.4 OTP Address Space on page 46, Section 9.7 One Time Program Array

Commands on page 111, and Section 9.7.2 OTP Read (OTPR 4Bh) on page 112.

8.1.1

Reading OTP Memory Space

The OTP Read command uses the same protocol as Fast Read. OTP Read operations outside the valid 1-kB OTP address range

will yield indeterminate data.

8.1.2

Programming OTP Memory Space

The protocol of the OTP programming command is the same as Page Program. The OTP Program command can be issued multiple

times to any given OTP address, but this address space can never be erased.

Automatic ECC is programmed on the first programming operation to each 16-byte region. Programming within a 16-byte region

more than once disables the ECC. It is recommended to program each 16-byte portion of each 32-byte region once so that ECC

remains enabled to provide the best data integrity.

The valid address range for OTP Program is depicted in Figure 42 on page 47. OTP Program operations outside the valid OTP

address range will be ignored and the WEL in SR1 will remain high (set to 1). OTP Program operations while FREEZE = 1 will fail

with P_ERR in SR1 set to 1.

8.1.3

Cypress Programmed Random Number

Cypress standard practice is to program the low order 16 bytes of the OTP memory space (locations 0x0 to 0xF) with a 128-bit

random number using the Linear Congruential Random Number Method. The seed value for the algorithm is a random number

concatenated with the day and time of tester insertion.

8.1.4

Lock Bytes

The LSB of each Lock byte protects the lowest address region related to the byte, the MSB protects the highest address region

related to the byte. The next higher address byte similarly protects the next higher 8 regions. The LSB bit of the lowest address Lock

Byte protects the higher address 16 bytes of the lowest address region. In other words, the LSB of location 0x10 protects all the Lock

Bytes and RFU bytes in the lowest address region from further programming. See Section 7.4 OTP Address Space on page 46.

8.2

Write Enable Command

The Write Enable (WREN) command must be written prior to any command that modifies non-volatile data. The WREN command

sets the Write Enable Latch (WEL) bit. The WEL bit is cleared to 0 (disables writes) during power-up, hardware reset, or after the

device completes the following commands:

–Reset

– Page Program (PP)

– Sector Erase (SE)

– Bulk Erase (BE)

– Write Disable (WRDI)

– Write Registers (WRR)

– Quad-input Page Programming (QPP)

– OTP Byte Programming (OTPP)

S25FL128SDPNFAQ Datasheet(PDF) 59 Page - Cypress Semiconductor

S25FL128SDPNFAQ Datasheet(HTML) 59 Page - Cypress Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL