| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
STW81200 Datasheet(PDF) 40 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
STW81200 Datasheet(HTML) 40 Page - STMicroelectronics |
|
40 / 58 page ![]() Circuit description STW81200 40/58 DocID025943 Rev 7 ST4 Register Address: STW81200BaseAddress + 0x04 Type: R/W Description: Lock det. control, Ref. Buffer, CP supply mode, VCO settings, Output power control 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 RW RW RW RW RW RW RW RW RW RW RW RW RW RW RW RW [26] RESERVED: must be set to ‘0’ [25:23] RF_OUT_PWR: RF output power control bit; set output power level of differential signal (valid for both RF1 and RF2 outputs; measured @ 4 GHz). When VCC_RFOUT is supplied at 2.6 V ‘0’ and ‘1’ are the only values allowed. 000: (0) -1.0 dBm (-4.0 dBm on each single-ended signal) 001: (1) +1.0 dBm (-2.0 dBm on each single-ended signal) 010: (2) +2.5 dBm (-0.5 dBm on each single-ended signal) 011: (3) +3.5 dBm (+0.5 dBm on each single-ended signal) 100: (4) +4.5 dBm (+1.5 dBm on each single-ended signal) 101: (5) +5.5 dBm (+2.5 dBm on each single-ended signal) 110: (6) +6.5 dBm (+3.5 dBm on each single-ended signal) 111: (7) +7.0 dBm (+4.0 dBm on each single-ended signal) [22] VCO_2V5_MODE: to be set to ‘1’ when VCO core (pin #3) is supplied at 2.6 V [21] RESERVED: must be set to ‘0’ [20] RESERVED: must be set to ‘0’ [19] EXT_VCO_EN: external VCO Buffer enable 0: external VCO buffer disabled; integrated VCOs are used 1: external VCO buffer enabled; external VCO required (internal VCOs are powered down) [18:15] VCO_AMP: set VCO signal amplitude at the internal oscillator circuit nodes; higher signal level gives best phase noise performance while lower signal level gives low current consumption. Different ranges of value are available, based upon the supply voltage provided to pin VCC_VCO_core (pin #3). Allowed settings: 0000 to 0110: (0-6) when VCO core is supplied at 2.6 V 0000 to 1010: (0-10) when VCO core is supplied at 3.3 V 0000 to 1111: (0-15) when VCO core is supplied at 4.5/5 V |
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |