| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
STM32U385CG Datasheet(PDF) 22 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
STM32U385CG Datasheet(HTML) 22 Page - STMicroelectronics |
|
22 / 224 page ![]() Mode name Entry Wake-up source Wake-up system clock Effect on clocks Voltage regulators Stop 3 LPMS = 011 + SLEEPDEEP bit + WFI or return from ISR or WFE WKUP pin edge, RTC/TAMP events/ interrupts (1), external reset in NRST pin, IWDG events/ interrupts (1) or reset, I3C reset pattern HSI16 when STOPWUCK = 1 in RCC_CFGR1 MSIS with the frequency before entering the Stop mode, limited to 48 MHz, when STOPWUCK = 0 All clocks OFF except LSI and LSE Low-power regulator (SMPS or LDO) Standby with SRAM2_ 8 Kbytes LPMS = 10x+ RRS1 = 1 + SLEEPDEEP bit + WFI or return from ISR or WFE MSIS from 3 MHz up to 12 MHz Standby with SRAM2_Full LPMS = 10x+ RRS1 = RRS2 = RRS3 = 1+ SLEEPDEEP bit + WFI or return from ISR or WFE Standby LPMS = 10x + RRS1 = RRS2 = RRS3 = 0 + SLEEPDEEP bit + WFI or return from ISR or WFE OFF Shutdown LPMS = 11x + SLEEPDEEP bit + WFI or return from ISR or WFE WKUP pin edge, RTC/TAMP events/ interrupts (1), external reset in NRST pin, I3C reset pattern MSIS 12 MHz All clocks OFF except LSE OFF 1. A wake-up event from Stop mode can be generated with the peripheral interrupt signal. By default, the microcontroller is in Run mode after a system or a power reset. It is up to the user to select one of the low-power modes described below: • Sleep mode CPU clock off, all peripherals including Cortex®-M33 core such as NVIC and SysTick can run and wake up the CPU when an interrupt or an event occurs. • Stop 0, Stop 1, Stop 2, and Stop 3 modes Stop mode achieves the lowest power consumption while retaining the content of SRAM and registers. The SRAMs can be totally or partially switched off to further reduce consumption. All clocks in the core domain are stopped. The MSI (MSIS and MSIK) RC, the HSI16 RC and the HSE crystal oscillators are disabled. The LSE or LSI is still running. The RTC can remain active (Stop mode with RTC, Stop mode without RTC). Some peripherals are autonomous and can operate in Stop mode by requesting their kernel clock and their bus (APB or AHB) when needed, in order to transfer data with GPDMA1 depending on peripherals and power mode. In Stop 0 mode, the regulator remains in main regulator mode, allowing a very fast wake-up time but with much higher consumption. In Stop 1, the regulator is in low-power mode, and the whole core domain is fully powered. All autonomous peripherals are functional. In Stop 2 mode, most of the core domain (D1 domain) is put in a lower leakage mode, keeping registers retention, but without any possible functionality. The D2 domain, embedding APB3 peripherals, is kept fully powered, so those peripherals can be kept functional. Stop 3 is the lowest power mode with full retention, but the functional peripherals and sources of wake-up are reduced to the same ones than in Standby mode. The system clock when exiting from Stop mode can be either MSIS up to 48 MHz or HSI16, depending on software configuration. STM32U385xx Functional overview DS14830 - Rev 2 page 22/224 |
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |